SCHOLTES TEC 645 L, Operating Instructions Manual

Page: 29 / 68

29
GB
F i x ing
T he appliance must be installed
on a per f ectly level
supporting sur f ace .
A ny de f ormities caused by improper f ixing could
a ff ect the f eatures and operation o f the hob .
T he thickness o f the supporting sur f ace should be
taken into account when choosing the length o f the
screws f or the f ixing hooks :
• 3 0 mm thick : 1 7 . 5 mm screws
• 40 mm thick : 7 . 5 mm screws
Fix the hob as f ollows :
1 . U se short f lat - bottomed screws to f ix the 4
alignment springs in the holes provided at the
central point o f each side o f the hob .
2 . Place the hob in the cavity, make sure it is in a
central position and push down on the whole
perimeter until the hob is stuck to the supporting
sur f ace .
3 . For hobs with raised sides : A f ter inserting the hob
into its cavity, insert the 4 f ixing hooks ( each has its
own pin ) into the lower edges o f the hob, using the
long pointed screws to f ix them in place, until the
glass is stuck to the supporting sur f ace .
T he screws f or the alignment springs must remain
accessible .
In order to adhere to sa f ety standards, the
appliance must not come into contact with electrical
parts once it has been installed .
All parts which ensure the sa f e operation o f the
appliance must not be removable without the aid o f
a tool .
E l e c t r i c a l c onne c t ion
T he electrical connection f or the hob and f or any
built - in oven must be carried out separately, both f or
sa f ety purposes and to make extracting the oven
easier .
T erminal b oar d
On the lower part o f the
appliance there is a
connection box f or the
di ff erent types o f electricity
supply ( the picture is only an
indication and is not an exact
representation o f the
purchased model ).
S in g le-p h ase c onne c tion
T he hob is e q uipped with a pre - connected electricity
supply cable, which is designed f or single - phase
connection . Connect the wires in accordance with
the instructions given in the f ollowing table and
diagrams :
Voltage and
mains frequency
Electrical cable Wire connection
220-240V 1+N ~
50/60 Hz
: yellow/green;
N: the two blue wires
together
L: brown and black
together
O t h er t y pes o f c onne c tion
I f the mains supply corresponds with one o f the
f ollowing :
V oltage and mains f re q uency
• 400 V - 2 +N ~ 50 /6 0 H z
• 220 - 240 V 3 ~ 50 /6 0 H z
• 400 V - 2 + 2 N ~ 50 /6 0 H z
Separate the wires and connect them in accordance
with the instructions given in the f ollowing table and
diagrams :
Voltage and
mains frequency
Electrical cable Wire connection
400V - 2+N ~
50/60 Hz
220-240V 3 ~
50/60Hz
: yellow/green;
N: the two blue wires together
L1: black
L2: brown
400V - 2+2N ~
50/60 Hz
: yellow/green;
N1: blue
N2: blue
L1: black
L2: brown
I f the mains supply corresponds with one o f the
f ollowing :
V oltage and mains f re q uency
• 400 V 3 - N ~ 50 /6 0 H z
proceed as f ollows :
T he cable provided is not suitable f or the f ollowing
types o f installation .
1 . U se a suitable supply cable, H 05 RR- F or higher,
with the right dimensions ( cable cross section : 25
mm ).
2 . T o open the terminal board, use a screwdriver as
a lever under the side tabs o f the cover ( see
T erminal b oard p icture ).
3 . L oosen the cable clamp screw and the terminal
board screws in accordance with the type o f
UNDERSIDE OF HOB