Schmidt MV3 Operation And Maintenance Manual Download Page 30

Page: 30 / 79

5.7 MV3 Valve (abrasive metering valve)

The MV3 Valve (#14) is used to control (meter) abrasive flow by use of an adjustable orifice.

The size of this orifice is controlled by turning the knob at the top of the MV3 Valve. Turning

the knob clockwise reduces the orifice size which decreases abrasive flow. Turning the knob

counterclockwise increases the orifice size which will increase the abrasive flow to the blast

nozzle (#11). Adjustments to the abrasive flow should be made by turning the knob a little at a

time. Test the adjustment by starting the blast for a short period to determine if further

adjustment is needed. The MV3 Valve has an orifice indicator on the body to use as reference

as to the amount the orifice is open.

Note:

For proper operation, the MV2® abrasive flow must

be in the direction of the base arrow (see Section 9.5(a)). However, this does not apply to MV3.

The MV3 Valve has a cleanout port used to purge trash that blocks abrasive flow. This is done

by removing the clean out cap and pressing down the deadman lever (#12). The blast air flow

purges trash through the clean out (see Section 11.3.2). The cleanout is then reinstalled for

operation.

Airborne particles and loud noise hazards from purged air can cause serious injury and loss of

hearing. Wear approved eye and ear protection. Stay clear of purge air path. DO NOT place hands

or other body parts in the purge air path. Make sure no personnel are in the purge air path.

5.8 Deadman Valve/Switch (blast control)

The Deadman valve/switch is part of the system that controls the blast operation. The deadman

allows the operator to remotely start and stop the blast operation. The deadman is mounted at

the end of the blast hose assembly (#10) near the blast nozzle (#11) to give the operator easy

control of the blast operation.

The Deadman is either a pneumatic valve or an electric switch depending on the type of

abrasive blaster control system. When the deadman lever is pressed down it sends either a

pneumatic or electric signal to the ComboValve®. The ComboValve opens and starts the blast

operation. See Sections 9.1, 9.2, 9.3, 9.8, and 9.9.

5.8.1.

Pneumatic Deadman System:

When the pneumatic deadman (#12) lever is pressed

down, air supply from the orange hose of the twinline hose (#15) flows into the black

hose. Air flows through the black hose to the signal port of the ComboValve (#4) to

open it and send air into the abrasive blaster and blast air hose. When the deadman lever

is released, the air signal is cut off and the ComboValve is closed to shut off the supply

air and depressurize the blaster through the blowdown hose assembly (#9). See Figure

5.3 and the drawings in Sections 9.1 and 9.2.

Figure 5.3 – MV3/Combo Pneumatic Deadman Blast Control System

Summary of Contents for MV3



























































Search results

Summary of Contents for MV3

Reviews:

Brands by name

Popular brands

Schmidt MV3, Operation And Maintenance Manual

Search results

Summary of Contents for MV3

Reviews:

Brands by name

Popular brands