3
TZKM/TZKF
Operating instructions
Solenoid interlock
EN
2.4 Technical data
Standards:
IEC 60947-5-1; EN 1088; EN ISO 13849-1;
BG-GS-ET-19
Enclosure:
glass-fibre reinforced thermoplastic
Actuator and locking bolt:
Galvanised steel / zinc die-cast
Protection class:
IP 67, IP 65 only with ordering suffix …NN
and …NF
Contact material:
Silver
Contact types:
Changeover contact with double break,
galvanically separated contact bridges
Switching system:
A
to IEC 60947-5-1; slow action, positi-
ve break NC contact
Termination:
Screw terminals
Cable type:
solid and stranded wire
Cable section:
min. 0.5 mm
2
, max. 2.5 mm
2
, (max. 1.5
mm
2
with conductor ferrules); compo-
nents with 4 contacts: min. 0.5 mm
2
,
max. 1.5 mm
2
(incl. conductor ferrules)
Cable entry:
2 x M20 x 1.5
U
imp
:
4 kV components with 4 contacts or 3
contacts with LED: 1.5 kV
Ui:
250 V components with 4 contacts or 3
contacts with LED: 60 VAC
I
the
:
4 A
Utilisation category:
AC-15, DC-13
I
e
/U
e
:
4 A / 230 VAC; 4 A / 24 VDC; compo-
nents with 4 contacts or 3 contacts with
LED: AC-15: 4 A / 60 VAC
Max. fuse rating:
4 A gG D-fuse (DIN EN 60269-1)
Positive break travel (un-
locked):
2 x 3.5 mm
Positive break force (un-
locked):
20 N
Magnet:
100 % ED
U
s
:
24 VDC, 24 VAC 50/60 Hz, 48 VAC
50/60 Hz, 110 VAC 50/60 Hz, 230 VAC
50/60 Hz
Power consumption:
max. 8.5 W
Actuating speed:
max. 20 m/min
Max. actuating frequency:
1,200 s/h
Ambient temperature:
0 °C … + 50 ºC
Mechanical life:
1 x 10
6
operations
F
max
:
1950 N
Latching force:
20 N
2.5 Safety classification
Standards:
EN ISO 13849-1
B
10d
(NC contact):
2,000,000
B
10d
(NO contact) at 10% ohmic
contact load:
1,000,000
Service life:
20 years
MTTF
B
d x
x
h
s/h
3600
d
10d
op
op
op
n
0,1 x n
op
t
cycle
(Specifications can vary depending on the application-specific parame-
ters h
op
, d
op
and t
cycle
as well as the load.)
3 Mounting
3.1 General mounting instructions
Three mounting holes are provided for fixing the enclosure. The soleno-
id interlock has double insulation. The use of a protective ground con-
nector therefore is not authorised. The solenoid interlock must not be
used as an end stop. Any mounting position, provided that the ingress
of dirt and soiling in the used opening is avoided. In case of painting
activities, the components must be covered. In case of horizontal fitting,
the cover plate (figure 1) located at the rear side of the actuating head
must be removed. If a different actuating direction is desired, the four
screws of the actuating head must be unscrewed. Turn the actuating
head in the desired direction and retighten the screws. (Tightening
torque 0.5 Nm). The default screws in the actuating head can be repla-
ced with the supplied tamperproof screws. For power-to-unlock compo-
nents (TZKF...), the actuator must be inserted when the actuating head
is turned. For fitting the components onto profile, the TZK/APL.. (figure
2) mounting plate must be used. After the assembly, the mounting plate
must be fixed (e.g. by pinning).
Please observe the remarks of the standards EN ISO 12100,
EN 953 and EN 1088.
When used in ambient temperatures > 40°C, the solenoid
interlock must be protected against contact with inflammable
materials or inadvertent personal contact.
Figure 1
Figure 2
3.2 Dimensions
All measurements in mm.
22,5
29,5
12
44
13
32
2,3
4,5
12
12
17,5
23,5
11
6
6
22
M 20
6
72
35
15
6
