schmersal SEP 01.0 Operating Instructions Manual Download Page 7

Page: 7 / 38

SEPK 02.0 / SEPG 05.3 / SEP 01.0 /

SEP 01.4 / SEPLC 05.2 / SEP 07.0 / SEP 09.0

Operating instructions

Two-hand control panel

Switching points:

NC contact: typ.1 mm

NO contact: typ.2.5 mm

Mounting position:

any

Mechanical life:

10 × 10

operations

Actuating force at stroke

end:

typ. 4.5 N

Connection:

Screw terminals

Cable section:

solid wire: 2 × (2 … 2 mm

)

stranded wire (with conductor ferrules):

2 × (2 … 2 mm

)

Tightening torque:

Connecting screw: max. 1 Nm

Shock-protection:

available (save illuminated element

individually mounted)

Approvals:

cULus (under preparation)

3.5 Technical data ADP... pushbutton

Standards:

IEC 947, EN IEC 60947, DIN VDE 0660,

DIN EN 50007, DIN EN 60068

Installation diameter:

22.3 mm

Front plate area:

1 … 6 mm

Connection:

Knurled nut, central mounting

Max. tightening torque:

1 Nm

Mounting position:

any

Temperature range:

–25 °C … +60 °C

Climate resistance:

to DIN EN 60068 Part 2-30

Protection class:

IP 65

Sealing type:

Lip gaskets, lat gaskets

Fully insulated:

Yes

Materials:

PA GV

Front ring execution:

PA GV

3.6 Technical data RF contact elements for ADP...

Standards:

EN IEC 60947, DIN VDE 0660,

DIN EN 60664, DIN EN 60068

Rated operating voltage

max.:

400 V

Utilisation category:

AC-13, DC-15

Operating current I

depending on the utilisation category and

the test voltage:

8 A: AC-15, 250 VAC

5 A: DC-13, 24 VDC

Thermal nominal current

Ith (in air):

10 A

Max. fuse rating:

gG 10 A

Air clearances and creepa-

ge distances

4 kV/3

Evidence of the positive

break:

2.5 kV impulse voltage

Positive break travel:

typ. approx. 2 mm after the opening point

Switching of low voltages

min. 24 VDC / 5 mA

Switching frequency to:

1,200 s/h

Temperature range:

–25°C … +60°C

Climate resistance:

Part 2-30

Mounting position:

any

Mechanical life:

10 × 10

operations

Switch travel:

typ.3.5 mm

Resistance to shock:

30 g / 16 ms

Resistance to vibrations:

20 g / 10 … 150 Hz

Wiring coniguration:

to EN 60947

Actuating force at stroke

end:

typ. 9 N

Switching points:

NC contact: typ.1 mm

NO contact: typ.2.5 mm

Enclosure material:

PA GV self-extinguishing, hardly lam-

mable

Connection:

Screw terminals

Cable section:

solid wire: 2 × (2 … 2 mm

)

stranded wire with conductor ferrules:

2 × (2 … 2 mm

)

Tightening torque:

Connecting screw max. 1 Nm

Rated insulation voltage U

: for degree of pollution 3: 400 V

Protection class:

Connections: IP 20 (inger-safe)

Switching elements: IP 40

Protection against acciden-

tal contact with live parts:

available (to EN 50 274 and BGV A2)

Approvals:

cULus

3.7 Technical data emergency stop command devices EDRR…,

KDRR…, ADR…, EDRZ… (Elan)

ED EFR + EF303.1 Command device, red colour,

mounting diameter 22.3 mm, head

diameter: 38.5 mm, 1 NO + 1 NC

ED EFR + EF303.1 Command device, red colour, moun-

ting diameter 1 mm, head diameter:

1 mm, 1 NO + 1 NC

KDR EFR +

EF303.1

Command device, red colour,

mounting diameter 22.3 mm, head

diameter: 38.5 mm, 1 NO + 1 NC

RF10 + RF03

Command device, red colour,

mounting diameter 22.3 mm, head

diameter: 40 mm, 1 NO + 1 NC

ED EF303.1

Command device, red colour, moun-

ting diameter 1 mm, head diameter:

1 mm, 1 NO + 1 NC

EF033.1 + EF220.1

Switching elements, 2 NO + 2 NC (in

separated form)

EF303.1 + EF303.2

Switching elements, 2 NO + 2 NC

(for emergency stop)

RF10 + RF10 + RF03 + RF03 Switching elements, 2 NO + 2 NC

(for A-programme emergency stop

with maximum equipment)

3.8 Technical data of the EDRR... emergency stop command device

Standards

IEC 60947-5-1, IEC 60947-5-5,

IEC 60947-1, EN ISO 13850

Design

round

Mounting

∅

22.3 mm

Spacing

for head Ø 40 mm: 50 × 40 mm,

for head Ø 50 mm: 50 × 50 mm

Front plate thickness

1 … 6 mm

Mounting position

any

Climate resistance to DIN

EN 60068

Part 2-30

Ambient temperature

–25 °C … +75 °C

Protection class to

IEC 605290

IP65

Fully insulated

yes

Material mushroom button Al anodised

Fixing

with mounting lange

Max. tightening torque for

the ELM ixing screws

0.6 Nm

Actuating force

approx. 25 N

Mechanical life

1 × 10

operations

Rohs compliant:

yes

Contact elements

Standards

IEC/EN 60947-5-1

Rated operating voltage

max.:

400 V

Rated insulation voltage U

for degree of pollution 3 to

EN 60 947-1:

400 V

Rated impulse withstand

voltage U

imp

4 kV

Thermal nominal current

(in air):

10 A

Summary of Contents for SEP 01.0







































Search results

Summary of Contents for SEP 01.0

Reviews:

Related manuals for SEP 01.0

Brands by name

Popular brands

schmersal SEP 01.0, Operating Instructions Manual

Search results

Summary of Contents for SEP 01.0

Reviews:

Related manuals for SEP 01.0

Brands by name

Popular brands