Schlosser KB55S Operating Instructions Manual Download Page 1

Page: 1 / 8

Schlosser
Aufzugtechnologie GmbH
Felix-Wankel-Straße 4
85221 Dachau
T +49 8131 / 5186-0
www.schlosser.de

Ausgabe
edition

06.09.2018

Seiten
pages

1/7

Bearbeiter
person in charge

Kepplinger

Zeichnung Nr.
drawing nr.

5370.800.001

Safety Module

Progressive safety gear - upward/downward acting = p weight of lift car in FREE fall
Braking device = 1/2 p masses UPWARDS upon tripping the overspeed governor incl. UCM/A3

Tension shoe

Releasing bolt

Kingpin, can be pulled out

Spring steel strip, inside

Lockwash

Douple eccentric

Kingpin, can be pulled out

Brake shoe retainer

Release slider

Brake shoe

Brake pads

Brake shoe

Operating Instructions

Safety Module Combination KB55S/SS-EB75GS

EU-SG 374/EU-SG 735 / EU-SG 289

General

General instructions

5370.800.002

Mounting/adjustment

5370.800.003

Mounting/adjustment/check

5370.800.004

Mounting/information

5370.800.005

Check

5370.800.006

Test instructions/information

5370.800.007

drawn: safety gear right
left mirrored

Normal position drawn

Summary of Contents for KB55S









Search results

Summary of Contents for KB55S

Reviews:

Related manuals for KB55S

Brands by name

Popular brands

Schlosser KB55S, Operating Instructions Manual

Search results

Summary of Contents for KB55S

Reviews:

Related manuals for KB55S

Brands by name

Popular brands