background image

Pulling out of the

 

l

 

engagement position

Downwards

l

 Engagement position: the brake shoes are pulled in upwards!

 

Pull off the 

l

 engagement position in steps:

 

- Start quickly in upward direction using the re-levelling control.

 

- Several repetitions = in principle: loosen and tighten ropes

 

- Handwheel aid

 

- Empty the car

 

- Traction sheave clamp, lifting etc. 

Safety gear KB55/S/SS 

Test instructions / Information

Schlosser 
Aufzugtechnologie GmbH
Felix-Wankel-Straße 4
85221 Dachau
T +49 8131 / 5186-0
www.schlosser.de

Ausgabe
edition

22.08.2019

Seiten
pages

7/7

Bearbeiter
person in charge

Kepplinger

Zeichnung Nr.
drawing nr.

5

2

60.800.007

Note

:

1.  In the case of weightless testing downwards (electronic test device), the bouncing of the cabin can cause the 

brake to fall back / pulled out of the engagement position! (Bouncing counterweight!). 

Note

:

The respective instructions of the different actuation variants (instructions) are packed „separately“ in the actuati-
on parts. Please note here also hints, which are complementary to the general instructions!

Engagement 

position 

Liability and guarantee:

The company Aufzugtechnologie Schlosser does 

not

 accept any liability or provide any guarantee for damages 

resulting from incorrect handling or inappropriate use of our products contrary to these instructions.

Summary of Contents for KB55








Reviews: