background image

© Allegion 2015

Printed in U.S.A.

23697279 Rev. 11/15-f

Customer Service

1-877-671-7011

www.allegion.com/us

Indicator Table

Condition

LED Indicator

Audible

Alarm Relay State

Standard Features

Lock Secure

Off

Off

Open

Authorized Release Input

Steady Green

Off

Open

During Nuisance Delay

Steady Red

Off (Default) 

Set by SW2-3

Open

During Fire Alarm

Steady Green

Off

Closed

During Delayed Egress

Flashing Red

Beeping

Closed

After Delayed Egress

Steady Green

Steady Tone

Closed

Switch Selectable Features

SW2-7 "ON" = Unlock Alert whenever lock is unlocked

Steady Green

Steady Tone

Open

SW2-3 "ON" = Horn will sound during nuisance alert

Steady Red

Steady Tone

Open

Optional Switch Selectable Features - Plus Model Required

Door Propped Open Alarm

Flashing Green

Beeping

Closed

Door Forced Open Alarm

Flashing Red

Steady Tone

Closed

Door Forced Open Alarm followed by Delayed Egress Input

Steady Green + Flashing Red

Steady Tone

Closed

Troubleshooting

Condition

LED Indicator

Lock has power but won’t lock. LED (on lock) is Green.

Fire alarm not connected or open connection. SW4-7 not ON (set switch, remove and 

re-apply power).

Won’t go into delayed egress.

Check dipswitch settings
Armature washers not installed properly
Magnet not properly aligned with armature.

Goes into delayed egress upon powerup.

Armature washers not installed properly
Improper gap between magnet and armature

Lock can be pushed open with minimal resistance.

Magnet/Armature/washers not installed properly

Lock “hums” or vibrates noisily when energized. 

Magnet/Armature/washers not installed properly

LED(s) flash once quickly.

Relock delay set to 0 sec.
Keypad not initialized

MBS doesn’t change state when locked.

Low voltage. Mechanical misalignment. Debris between lock and armature. Armature/

magnet not installed properly

DPS option not working properly.

Armature holder not aligned with DPS switch. 
Switch not plugged into correct jack

BOCA Operational Description

 

L

BOCA Option is Applicable in United States Jurisdictions Only

a.  Lock the door and start the release process by pushing on the actuating bar (or door if no actuating bar provided) for at least 1 second. 

The door will release within 15 seconds.

b.  The door will not relock until the door has been opened, and returned to the closed position for not less than 30 seconds. Any reopening 

of the door during this time will restart the 30 second relocking cycle.

c. 

A 30 second release time delay may be provided with code official approval.

Summary of Contents for M490DE













Reviews: