manualshive.com logo in svg

Schlage KING COBRA-2 KC5196-2-R, Installation Manual

Share
Download
Schlage KING COBRA-2 KC5196-2-R Installation Manual Download Page 23

KC9111/KC9111-2 & KC9321/KC9321-2 INSTALLATION

Installing the KC9111/KC9111-2 or KC9321/KC9321-2

57040-E                                              Page 23                                              04-2007

39)  Install Batteries:

40)  Fold Battery Bag:

41)  Install Battery Pack:

•     

Remove and retain battery bag.

IMPORTANT: DO NOT DISCARD BATTERY BAG. IT IS IMPORTANT 
THAT IT IS REINSTALLED AFTER THE BATTERIES ARE INSTALLED 
IN BATTERY HOLDER.

•     

Observe the polarity markings indicated on battery holder and install 

four, AAA batteries accordingly.

•     

Slide battery bag onto battery holder.

•     

Fold battery bag over.

IMPORTANT: The battery bag is used to protect the batteries 
from moisture and to insulate them electrically from metallic 
parts.

•     

Install battery pack into compartment with bag open-

ing facing down.

•     

Tuck wiring neatly into compartment

Summary of Contents for KING COBRA-2 KC5196-2-R





























Reviews:

No comments

Brands by name

Popular brands

Load more brands