manualshive.com logo in svg

Schiller Grounds Care Ryan 544951H, Operations & Parts Manual

Share
Download
Schiller Grounds Care Ryan 544951H Operations & Parts Manual Download Page 28

26

Jr.

Sodcutter

SPECIFICATIONS

Models: 544951H......Jr. Sodcutter - 12 in.(30.5cm)

 

  544952H......Jr. Sodcutter - 18 in.(45.7cm)

Engine

Model.............4 cycle 6.5H.P.(4.8KW) B&S Vanguard, 

Model 12H332, Type 0159,

Trim B8, 12.5 cu. in. (205 cc) 

Starter...................................................... Recoil

Governor.......... 

3600 RPM + 100 RPM, no load

Clutch............... 

spring loaded belt tightener type

Reduction

Engine to blade....................................... 

2.94:1

Engine to drive wheels............................ 

55.8:1

Models: 544953C.....Jr. Sodcutter - 12 in.(30.5cm)

               544954C.....Jr. Sodcutter - 18 in.(45.7cm)

Engine

Model................ 

4 cycle 5.5 H.P. Honda 

Model GX160-K1QX2, GX160 OHV

9.9 cu. in. (163 cc)

Starter...................................................... Recoil

Governor.......... 

3600 RPM + 100 RPM, no load

Clutch............... 

spring loaded belt tightener type

Reduction

Engine to blade....................................... 

2.94:1

Engine to drive wheels............................ 

55.8:1

Wheels:

Drive................. 

8" (203 mm) Dia. w/knobby

 

tread vulcanized to hub

Rear.............8 x 1.75 (203 X 45mm)  semi-pneumatic 

tires

 

with pre-packed ball bearings

Drive:

Engine to gear case................. 

"A" section belt

Gear case to drive shaft 

and blade drive...........................................roller chain

Gear case:

Lubrication.................................. 

EP140 Gear lube

Capacity...................................... 

3 1/2 Pints (1.7L)

Cutting width:

544951H & 544953C..................11 3/4" (298 mm)

544952H & 544954C........................18" (457 mm) 

Blade pitch:

Hand lever adjustment............... 

variable 0

O

 to 9

O

Blade speed:

 .....

1225 oscillations/min @ 3600 engine RPM

Dimensions:

Width.......................................... 

24" (600 mm)

Length........................................          49" (1244 mm)

Height......................................... 

33" (838 mm)

Wheelbase................................. 

19" (483 mm)

Weight:

 544951H & 544953C................ 

333 lbs. (151 Kg)

  544952H  &  544954C................ 

377  lbs.  (171  Kg)                              

TOUCH -UP PAINT:  

   

16OZ. (0.5L) Spray can, order P/N 65334

Summary of Contents for Ryan 544951H











































Reviews:

No comments

Brands by name

Popular brands

Load more brands