manualshive.com logo in svg

Schiller Grounds Care Ryan 544951H, Operations & Parts Manual

Share
Download
Schiller Grounds Care Ryan 544951H Operations & Parts Manual Download Page 20

18

Jr.

Sodcutter

MAINTENANCE

DRIVE BELT REPLACEMENT

1.  Remove shield on left side of unit.

2.  Remove nut securing brake band to clutch 

control rod.

3.  Remove cotter pin on outside of guard support 

rod and move brake band over to nut on rod. 

4.  Loosen two bolts 

A

 securing belt guide to  

provide clearance when removing belt.

5.  Remove belt from engine pulley.  To do this, 

loosen upper and lower belt guards, or remove 

the engine pulley.

6.  Install new belt in reverse procedure. Route the 

belt as shown.

7.  Adjust belt and brake band.  See Adjustment 

Section.

DRIVE CHAIN REMOVAL

1.  Raise unit, place on adequate supports and 

remove belt guard. 

2.  Remove four (4) screws securing gear case 

cover.

3.  Remove throttle cable from engine and lay 

behind cam case.

4.  Remove dipstick from cover.

5.  Remove screw, flat washer, nut and bushing from 

right lower side of "H" frame.

6.  Using a screwdriver, lift gear case cover to break 

sealant bond and remove cover.

7.  Drain oil out of front cavity on case, and turn 

drive wheels until master link is on top of 

sprocket.

8.  Connect new chain to old with master link.  

Rotate drive wheels until  new chain is pulled 

around.  Remove old chain and connect new 

chain with a new master link.

9.  Complete installation by reversing procedure   

Clean mating surfaces on case and cover. Apply 

3M Scotch Grip 847 or an equivalent adhesive to 

case cover before installation.

Summary of Contents for Ryan 544951H











































Reviews:

No comments

Brands by name

Popular brands

Load more brands