manualshive.com logo in svg

Schiller Grounds Care BOB-CAT 942311G, Parts And Operator'S Manual

Share
Download
Schiller Grounds Care BOB-CAT 942311G Parts And Operator'S Manual Download Page 36

34

FastCat RZ

HYDROSTATIC TRANSAXLE ADJUST-
MENTS

A turnbuckle style hydrostat neutral adjustment is 
provided.  

Neutral:

  

1.   Support the machine with the rear wheels off 

the ground.  Use jackstands or equivalent sup-
port.  Do not rely only on mechanical or hydraulic 
jacks.  

2.   Move the traction levers out into the neutral lock 

position and raise the seat.

3.   Disconnect the seat switch wire and temporarily 

connect the two terminals with jumper wire 

J

 as 

shown. 

4.  Start the engine and run at low speed.
5.  Move parking brake to the 

OFF

 position.  

6.  Loosen jam nuts 

K

 at both ends of the control 

rod 

L

.

7.  Rotate the control rod until the corresponding 

wheel stops turning.  Lock the control rod jam 
nuts.  Run the engine up to high idle and stroke 
the traction levers forward and back to check the 
adjustment.  Move traction levers back to neutral 
and readjust if necessary.  

8.  Repeat steps 6 and 7 for the opposite side.
9.  Remove the jumper wire and reconnect the seat 

switch.

ADJUSTMENTS

Summary of Contents for BOB-CAT 942311G









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands