manualshive.com logo in svg

Schiller Grounds Care BOB-CAT 942311G, Parts And Operator'S Manual

Share
Download
Schiller Grounds Care BOB-CAT 942311G Parts And Operator'S Manual Download Page 20

18

FastCat RZ

CONTROLS

PARKING BRAKE (R)

 - Pull the parking brake 

lever up and back to put the parking brake ON.  Push 
it forward and down to put the parking brake OFF.  

The parking brake must be ON to start the engine.  
It must also be ON to keep the engine running if the 
operator leaves the seat.  The parking brake must be 
OFF to keep the engine running when a traction lever 
is moved out of neutral lock.

Parking brake in ON position 

(operator's left side)

PUSHING THE MACHINE

The machine may be pushed with the engine off, the 
parking brake off, and the bypass valves open.

To open the bypass valves, move the parking brake 
to the 

OFF

 position, then lift and pull bypass control 

rod 

C

 through the large opening 

D

, until the control 

rod stop is past the opening.  Drop rod 

C

 into the 

small opening to lock in place.  Repeat for the other 
bypass control rod.

To close the bypass valves, lift bypass control rod 

C

 

allowing the control rod stop to retract through the 
large opening 

D

.

Summary of Contents for BOB-CAT 942311G









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands