www.scheppach.com
GB | 27
• Do not install the compressor in a damp or wet room.
• The compressor may only be used in suitable rooms
(with good ventilation and an ambient temperature
from +5 °C to 40 °C). There must be no dust, acids,
vapours, explosive gases or inflammable gases in
the room.
• The compressor is designed to be used in dry rooms.
It is prohibited to use the compressor in areas where
work is conducted with sprayed water.
•
The compressor may only be used outdoor briefly
when the ambient conditions are dry.
• The compressor must always be kept dry and must
not be left outdoors after work is complete.
10. Attachment and operation
m
Attention!
Always make sure the device is fully assembled
before commissioning!
You require the following for assembly:
1x open-ended spanner 12 mm, 13 mm and 17 mm
(not included in the scope of delivery)
10.1 Fitting the wheels
(fig. 3)
• Fit the supplied wheels (5) as shown.
10.2 Fitting the foot
(fig. 4)
• Fit the supplied foot (7) as shown.
10.3
Fitting the air filter
(fig. 5, 6)
•
Remove the transport lid (15) and screw the air filter
(4) to the equipment.
•
Insert the hose (4d) into the opening of the air filter
(4).
10.4 Fitting the transport handle
(fig. 11)
• Fit the supplied transport handle (1) as shown.
10.5 Mains connection
• The compressor is equipped with a mains cable with
protective contact plug. This can be connected to
any 220 ‒ 240 V
∼
50 Hz protective contact socket,
with fuse protection of at least 16 A.
• Before you use the machine, make sure that the
mains voltage is the same as the operating voltage
and the machine power on the rating plate.
• Long supply cables, extensions, cable reels, etc. cause
a drop in voltage and can impede motor start-up.
• At low temperatures below +5 °C, sluggishness may
make starting difficult or impossible.
Noise and vibration
m
Warning
: Noise can have serious effects on your
health. If the machine noise exceeds 85 dB (A), please
wear suitable hearing protection.
Noise data
Sound power level L
WA
87 dB(A)
Sound pressure level L
pA
60 dB(A)
Uncertainty K
wa/pA
3 dB(A)
The noise emission values have been determined in
accordance with EN ISO 3744:1995.
8. Unpacking
• Open the packaging and carefully remove the device.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating instructions before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Replace-
ment parts can be obtained from your dealer.
• When ordering please provide our article number as
well as type and year of manufacture for your equip-
ment.
m
WARNING!
The device and the packaging material are not
children’s toys! Do not let children play with plas-
tic bags, films or small parts!
There is a danger of
choking or suffocating!
9. Before commissioning
• Before connecting the machine, make certain that
the data on the type plate matches with the mains
power data.
• Check the device for transport damage. Report any
damage immediately to the transport company which
was used to deliver the compressor.
• Install the compressor near the point of consumption.
• Avoid long air lines and supply lines (extension cables).
• Make sure that the intake air is dry and free of dust.
Summary of Contents for HC25Si
