www.scheppach.com
+(49)-08223-4002-99
+(49)-08223-4002-58
39 І 180
www.scheppach.com
+(49)-08223-4002-99
+(49)-08223-4002-58
Uncertainty K
wA
3 dB
Vibration Front handle
7.5 m/s²
Vibration Rear handle
7.0 m/s²
Uncertainty
1.5 m/s²
7. Before starting up
m
CAUTION!:
Start the engine only when the saw is
fully assembled.
m
CAUTION!:
When handling the chain always wear
protective gloves.
Assembling the bar, and the chain
(Fig. 3-6)
Open the box and assemble the bar and chain as fol-
lows:
1. Press the front hand guard back (Fig.14/Pos.3a)
so that the chain brake is disabled.
2. Loosen the two nuts (B) and remove the cover
(17) and spacer (A).
3. Mount the bar on the two threaded pins (Fig.4)
4. Slide the chain around the sprocket, next slide
the saw chain around the bar. Pay attention to the
installation direction of the chain. (Fig.4-5)
5. Insert the chain tensioning screw (Z) into the low-
er hole of the chain bar (Y). (Fig.4)
6. Install the cover (17) and tighten the nuts (B) by
hand.
Installation direction of the chain (shown Fig. 5)
Tensioning the chain (Fig. 6-8)
1. Hold the front part tight with your hand.
2. Adjust the chain tension using the tension screw
(C) so that the chain rests entirely on the bar, but
not under great tension.
3. Tighten the mounting nut (B) for the bar with the
key (12-15 Nm).
4. Check with your hand that the chain runs smooth-
ly on the rail and has the proper voltage.
5. Where necessary, set up the chain tension.
m
NOTE
If the chain is too loose or too tight on the drive wheel
and bar, the crankshaft bearings will wear out faster.
m
NOTE
New chains expand, so they must be reset after
about 5 cuts. This is normal for a new chain, and the
future interval settings will decrease.
6. Technical data
Machine without guide
bar L x W x H
430 x 255 x 250 mm
Weight without guide
bar and saw chain and
empty tank
5.5 kg
Weight with guide bar
and saw chain and
empty tank
6.0 kg
Cutting Length
430 mm
Guide bar length
457 mm
Automatic chain oiling
yes
Saw chain Oil
Special saw chain Oil
Saw chain oil tank ca-
pacity
0.26l
Saw chain division
3/8″
Drive link thickness
1.27 mm
Saw chain type
Oregon 91PX062X
Number of teeths drive
sprocket
7
Tooth pitch of drive
sprocket
3/8″
Chain brake
yes
Guide bar type
Oregon
180SDEA095
Saw chain speed max.
22 m/s
Motor
1 cylinder
2 stroke
air-cooled
Engine capacity
46 cm³
Maximum motor capac-
ity
2.0 kW
Idle speed
3300±200 min
-1
Maximum speed with
cutting attachment
11000 min
-1
Fuel tank capacity
0.55 l
Fuel type
Mix 40:1
Keep the noise emissions and vibrations to a
minimum.
• Only use appliances which are in perfect work-
ing order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Measured sound pressure level L
pA
99 dB(A)
Uncertainty K
pA
3 dB
Guaranteed sound power level L
wA
114 dB(A)
Measured sound power level L
wA
109.9
dB(A)
GB
