22
www.scheppach.com
+(49)-08223-4002-99
+(49)-08223-4002-58
10. Electrical connection
The installed electric brake motor is ready to be put
into operation.
The connection meets the relevant VDE and DIN re-
quirements.
The electric brake motor causes the disc blade to
come to a near immediate standstill after the machine
has been turned off.
Firring, repair and maintenance work on the electric
unit can only be carried out by a qualified electrician.
Important notes
Damaged electrical connection cables
Insulation damage often occurs with electrical con-
nection cables.
Some causes are:
•
Pressure points, especially when electrical connec
-
tion cables are run through window or door cracks.
•
Kinks caused by improper handling or mowing of
the electrical connection cables.
• Cuts resulting from being run over
•
Insulation damages caused by pulling the cable out
of wall sockets.
• Cracks resulting from aging of the insulation.
Such insulation damaged electrical connection cables
cannot be used and are, as a result of their insulation
damage.
LIFETHREATENING!!
Check the electrical cable connections on a regular
basis. When checking the cables, make sure that the
cables are not stuck to the electrical network.
Electrical cable connections built with seal contacts
must meet the relevant VDE and DIN requirements.
Only use electrical cable connections with a rating of
at least H 07 RN or a rubber sheathed cable.
The type rating of the connection cable must be print
-
ed on the cable.
Single-phase motor
• The mains voltage must comply with the specifica
-
tions on the motor nameplate.
• Extension cables up to 25 m in length must have a
cross section of at least 1,5 mm² , above 25 m at
least 2,5 mm²
• Mains fuse protection is 10 Amps slow-blow.
In accordance with safety regulations, the motor is
equipped with a switch featuring an integrated pro-
tective circuitbreaker, which cuts off the current in the
event of
overload.
Overload may be caused by the following:
• longer-duration blockage of the knife disc
• alternately switching on/off of the motor in rapid
succession
In the event of a blocked knife disc, remove the cause
to the overload. Disconnect the mains plug. After a
short cooling-off time , switch back on the motor.
9. Maintenance
NJURY WARNING
!
Before working on the device, disconnect the
mains cable from the socket.
Always wear protective gloves when working on
or around cutting tools.
The user is responsible for all damages caused by
non-compliance with instructions in this manual. This
also applies to non-authorized modifications of the
tool, use of non-authorized spare parts, accessories,
working tools, unrelated and not intended use,
secondary damages due to use of faulty components.
•
Regularly check the device before starting work.
•
Only use OEM parts for maintenance work. Using
parts other than original parts can cause damage
to the machine.
• This tool is not intended for professional use
•
Always keep tool and cord clean (especially venti
-
lation slots J)
• Clean the mower after each use with a hand brush
and a soft cloth
•
! do not use water (especially no high-pressure
sprays)
• remove compacted grass cuttings from the blade
area with a wooden or plastic implement
•
Regularly check the grass box for wear or damage
•
Regularly check for worn or damaged blades and
boltsand have them replaced in sets to preserve
balance
Changing the blade
• ! disconnect plug from power source and remove
grass box (G)
• ! wear protective gloves
• turn the mower upside down
•
Hold the blade firmly and remove/fit the blade wi
-
th a size 19 wrench, by turning anticlockwise.
•
Make sure you only use original spare blades!
•
thoroughly clean the shaft area and the underside
of the tool before mounting the cutting blade
• If the tool should fail despite the care taken in ma-
nufacturing and testing procedures, repair should
be carried out by an authorized service centre.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consuma-
bles.
Wear parts*: wheels, blade
* Not necessarily included in the scope of delivery!
