Scheppach 5903405901, Translation Of Original Instruction Manual

Page: 24 / 128


www.scheppach.com /

service@scheppach.com /

+(49)-08223-4002-99 /

+(49)-08223-4002-58
24 | GB
6. Technical data
Dimensions L x W x H 465x420x500 mm
Speed 2000 1/min
Oscillation stroke 16 mm
Belt dimensions 610 x 100 mm
Belt Speed 8 m/s
Grinding height max. 90 mm
Spindle ø 12.6 mm
Table Size 410 x 425 mm
Table Tilt 0° - 45°
Vacuum connector ø 38 mm
Weight 12.9 kg
Motor 220-240 V~ / 50 Hz
Power 450 W
Subject to technical changes!
Total vibration values determined in accordance with
EN61029
sound pressure level L
PA
76 dB(A)
uncertainty K
pA
3 dB
sound power level L
WA
89 dB (A)
uncertainty K
WA
3 dB
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total
vibration values (vector sum - three directions) deter-
mined in accordance with EN 61029.
7. Unpacking
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately.
• Later claims will not be recognised.
• If possible, store the packaging until the warranty
period has expired.
• Familiarise yourself with the product by means of
the operating instructions before using for the first
time.
• With accessories as well as wearing parts and re-
placement parts use only original parts.
• When ordering please provide our article number
as well as type and year of manufacture for your
equipment.
• IMPORTANT: Mount and use the machine on a
horizontal surface. A non-horizontal surface can
damage the motor.
• If the machine tends to tilt or walk (especially when
sanding long and heavy panels), it must be fas-
tened to a solid surface of sufficient carrying force.
• Firmly hold the workpiece when sanding.
• Do not wear gloves. Do not hold the workpiece with
a cloth during sanding.
• Never sand workpieces too small to be held safely.
• Avoid awkward hand positions where a sudden slip
could cause your hand to touch the sanding belt
or disc.
• When sanding a large piece of material, provide an
additional support at table height.
• Never sand an unsupported workpiece. Secure the
workpiece with the table or the fence. Exceptions
are the sanding of curved workpieces on the out-
side of the sanding disc.
• Always clear the table, fence or sanding belt of
scraps or other objects, before turning the machine
on.
• Do not perform any layout assembly or set-up work
on the table while the sanding machine is in oper-
ation.
• Switch the machine off and pull the power plug from
the socket when fitting or removing accessories.
• Never leave the working area of the sanding ma-
chine while the tool is running, or as long as it has
not come to an absolute standstill.
• Always place the work piece on the grinding table.
To sharpen bent tools with the grinding disc, place
them securely on the table.
Remaining hazards
The machine has been built using modern technology
and in accordance with recognized safety rules.
Some hazards, however, may still remain.
• The grinding wheel poses a danger of injury to fin -
gers and hands by improper feeding or placement
of tools.
• Danger of injury from thrown tools due to improper
holding or feeding.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Although having regarded all considerable rules
there may still remain not obvious remaining
hazrds.
• Residual risks can be minimised if the “safety in-
structions” and the “Proper use” are observed
along with the whole of the operating instructions.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.