www.scheppach.com /
+(49)-08223-4002-99 /
+(49)-08223-4002-58
22 | GB
Vibration emission value a
h
≤ 2.5 m/s
2
K uncertainty = 1.5 m/s
2
Warning!
The specified vibration value was established in ac
-
cordance with a standardized testing method. It may
change according to how the electric equipment is
used and may exceed the specified value in excep
-
tional circumstances.
The specified vibration value can be used to com
-
pare the equipment with other electric powertools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect working
-
order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
• Do not overload the appliance.
•
Have the appliance serviced whenever necessary.
•
Switch the appliance off when it is not in use.
• Wear protective gloves.
7. Assembly
Before you connect the equipment to the mains sup
-
ply make sure that the data on the rating plate are
identical to the mains data.
Always pull the power plug before making adjust
-
ments to the equipment.
Pull the power plug before doing any maintenance
or assembly work on the equipment.
•
The machine must be set up so that it stands firm
-
ly, i.e. it must be securely screwed to a work bench
or similar.
•
All covers and safety devices have to be properly
fitted before the equipment is switched on.
•
The grinding wheels must rotate freely.
• Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the equipment to the power supply.
Warning! Never connect the plug to power source
outlet until all installations and adjustments are com-
pleted and you have read and understood the safety
and operation instructions.
Tool support (left and right) (Fig. 1, 2, 2.1)
Fasten the tool support (4) to the grinding wheel
guard (6) with the mushroom head screw (M6x10) (a)
and the star grip nut (b).
The distance between wheel and work rest should
not exceed 2 mm.
•
Do not use any damaged or deformed grinding
wheels or brushes.
•
Only use grinding wheels and brushes marked with
a rotational speed which is at least as high as the
speed indicated on the rating plate of the electrical
tool.
•
Always leave the brush fastened to the spindle in
order to limit the risk of contact with the rotating
spindle.
6. Technical Data
Delivery
Bench Grinder
SM150LB
User’s Manual
Technical Data
Dimensions L x W x H
380 x 210 x 280 mm
Grinding disc max.
ø 150 mm
Grinding disc min. (after
wear and tear)
ø 110 mm
Brush max.
ø 150 mm
Brush min. (after wear)
ø 120 mm
Grinding disc bore max
ø 12,7 mm
Brush bore max.
20 mm
Brush width
13,5
Lamp
LED with battery (2x)
Weight
7 kg
Motor
Motor
230-240/50 V/Hz
Input power S2 10 min
400 W
Motor speed
2850 1/min
Subject to technical changes!
Load factor:
A load factor of S2 10 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (400 W) for no longer than
10 minutes ON period. If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
Sound and vibration
Sound and vibration values were measured in ac-
cordance with EN 62841.
L
pA
sound pressure level
64,9 dB(A)
K
pA
uncertainty
3 dB
L
WA
sound power level
76,1 dB(A)
K
WA
uncertainty
3 dB
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Total vibration values (vector sum of three directions)
determined in accordance with EN 62841.