www.scheppach.com
34 | GB
Wear parts*: Carbon brushes, saw blade, table inserts,
dust collecting bags, V-belts
* Not necessarily included in the scope of delivery!
Spare parts and accessories can be obtained from our
service centre. To do this, scan the QR code on the
cover page
11. Storage
• Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
• The optimum storage temperature is between 5 and
30˚C.
• Store the electrical tool in its original packaging.
• Cover the electrical tool in order to protect it from
dust and moisture.
• Store the operating manual with the electrical tool.
12. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies with
the applicable VDE and DIN provisions. The custom-
er‘s mains connection as well as the extension cable
used must also comply with these regulations.
• The product meets the requirements of EN 61000-
3-11 and is subject to special connection conditions.
This means that use of the product at any freely se-
lectable connection point is not allowed.
• Given unfavorable conditions in the power supply
the product can cause the voltage to fluctuate tem
-
porarily.
• The product is intended solely for use at connection
points that
a) do not exceed a maximum permitted supply im-
pedance “Z” (Zmax. =
0.407 Ω), or
b) have a continuous current-carrying capacity of
the mains of at least 100 A per phase.
• As the user, you are required to ensure, in consulta-
tion with your electric power company if necessary,
that the connection point at which you wish to oper-
ate the product meets one of the two requirements,
a) or b), named above.
Important information
In the event of an overloading the motor will switch it-
self off. After a cool-down period (time varies) the mo
-
tor can be switched back on again.
•
To switch off:
Move the ON/OFF switch of the laser
(35) to the “0” position.
8.12 Adjusting the laser (Fig. 10)
If the laser (34) ceases to indicate the correct cutting
line, you can readjust the laser. To do so, open the
screws (36) and set the laser by moving sideways to
that the laser beam strikes the teeth of the saw blade
(7).
9. Transport (Fig. 1, 2)
• Tighten the set screw (26) in order to lock the ro-
tary table (16)
• Press the machine head (5) downwards and secure
with the safety pin (24). The saw is now locked in
its bottom position.
• Fix the saw’s drag function with the locking screw
for drag guide (23) in rear position.
•
Carry the equipment by the fixed saw table (17).
• When reassembling the equipment proceed as de-
scribed under section 7.1.
10. Maintenance
m
WARNING!
Prior to any adjustment, maintenance
or service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time
using a cloth. In order to extend the service life of
the tool, oil the rotary parts once monthly. Do not oil
the motor.
When cleaning the plastic do not use corrosive prod-
ucts.
Brush inspection
Check the carbon brushes after the first 50 operating
hours with a new machine, or when new brushes have
been fitted. After carrying out the first check, repeat
the check every 10 operating hours.
If the carbon is worn to a length of 6 mm, or if the
spring or contact wire are burned or damaged, it is
necessary to replace both brushes. If the brushes are
found to be usable following removal, it is possible to
reinstall them.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consumables.
Summary of Contents for 5901218901
Page 113: ...www scheppach com 113...
Page 114: ...www scheppach com 114 HM1247...