www.scheppach.com
26 | GB
Cleaning
Dust can collect in the belt and disc grinder. Check
regularly (preferably after every use) and remove dust,
e. g. by blowing away or carefully with compressed air.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consum-
ables.
Wear parts*: Carbon brushes, v-belt, grinding medium
* Not necessarily included in the scope of delivery!
Spare parts and accessories can be obtained from our
service centre. To do this, scan the QR code on the
cover page.
12. Storage
Store the device and its accessories in a dark, dry and
frost-proof place that is inaccessible to children. The
optimum storage temperature is between 5 and 30˚C.
Cover the electrical tool in order to protect it from dust
and moisture.
Store the operating manual with the electrical tool.
13. Electrical connection
The installed electric motor is connected and is ready
to work.
The connection complies with the relevant VDE and
DIN regulations.
The customer-side mains supply and the used exten-
sion line must meet these regulations.
Damaged electrical connection cable.
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Passage points, where connection cables are
passed through windows or doors.
• Kinks where the connection cable has been improp-
erly fastened or routed.
• Places where the connection cables have been cut
due to being driven over.
• Insulation damage due to being ripped out of the
wall outlet.
• Cracks due to the insulation ageing.
Sanding curved pieces, see fig. 18
Warning: Never attempt to sand the end pieces of a
workpiece on the idler drum (R). Applying the end of
the workpiece on the idler drum could cause the work-
piece (W) to fly up. Failure to heed this warning could
result in serious personal injury.
Always sand inside curves on the idler drum as shown
in Figure 18.
•
Hold the workpiece firmly, keeping fingers away
from the sanding belt.
•
Keep the curve pressed firmly against the idler drum
moving work evenly across the sanding belt.
Note: Use extra caution when sanding very thin pieces
and apply only enough pressure to allow the sanding
belt to remove the material.
Sanding outside curves on sanding disc fig. 19
Always sand outside curves using the sanding disc
and moving the workpiece (W) from the left side of
center as shown in Figure 19
•
Hold the workpiece firmly, keeping fingers away
from the sanding disc.
•
Keep the curve pressed firmly against the sand
-
ing disc moving work evenly on the left side of the
sanding disc.
Warning: Applying the workpiece to the right side of
the sanding disc could cause the workpiece kickback.
Failure to heed this warning could result in serious per-
sonal injury.
11. Cleaning and maintenance
Important.
Warning! Prior to any adjustment, maintenance or ser-
vice work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time
using a cloth. In order to extend the service life of the
tool, oil the rotary parts once monthly. Do not oil the
motor.
When cleaning the plastic do not use corrosive product.
General maintenance
After using your belt/disc sander, clean it completely
and lubricate all sliding and moving parts. Apply a light
coat of automotive type paste wax to the worktable to
help keep the surfaces clean.
Summary of Contents for 4903302901
Page 2: ...www scheppach com 2 12 1 2 7 3 14 5 13 11 9 10 8 6 4 15 16 1 14 14 1 17 7 1 2 3 4 5...
Page 3: ...www scheppach com 3 5 20 17 15 16 1 14 20 18 19 10 6 6 7 8 9 10 11 12 13...
Page 4: ...www scheppach com 4 X W W R W 7 0 15 45 max 1 6 mm 3 6 14 13 14 15 16 17 18 19...
Page 86: ...www scheppach com 86...