manualshive.com logo in svg

Schacht BABY WOLF LOOM, Assembly Instructions Manual, Page: 12 / 13

Share
Download
Schacht BABY WOLF LOOM Assembly Instructions Manual Download Page 12

- 12 -

21. 

Install the warp beam crank handle. 

Parts: 1 – warp beam crank handle, 1 – 3/8" washer,  
1 – 3/8" cap nut. 
 
Place the 3/8" washer and then the metal crank handle 
on the threaded shaft extending through the leg from the 
brake end of the warp beam. The wood crank handle faces 
away from the loom. Secure with the 3/8" cap nut. Tighten 
the nut by placing the handle over it and turning clockwise. 
To engage the crank for turning the warp beam, pull the 
hexagonal hole in the crank onto the cap nut. While weav-
ing, the crank should be pushed off the cap nut.

Inside 

left leg

back beam

fender washer

black knob

barrel nut

Figure 24 - iNSTALL THe reMOVABLe BACK BeAM

beater pin

beater pin chain

beater pin holder

1/2" screw

Figure 25 - iNSTALL THe BeATer PiN HOLDer

beater pin and 

holder

23. 

Install the beater pin.

 

Parts: Beater pin with chain, beater pin holder, 1 – #6 x 
1/2" screw.  
 
Put the screw through the hole in the end of the beater pin 
chain and through the hole in the beater pin holder. Fasten 
it to the small pilot hole in the right leg. There will be a  
hole between the pilot hole and the screw holding the fold 
support bar.

  

 

The beater pin is used to hold the beater upright during 
warping. Push the pin through the hole in the leg and then 
through the slot in the beater side. Remember to pull the 
beater pin out and replace it in its holder before weaving or  
folding the loom.

22. 

Install the removable back beam. 

 

Parts: Back beam, 2 – 1/4" black knobs, 2 – fender wash-
ers, 2 – 1/4" barrel nuts. 
 
Slide the back beam into the slots cut in the top of the 
inside legs. Put a fender washer on a knob, and insert the 
knob through the leg, into the back beam, and tighten it 
into a barrel nut in the back beam. Repeat for the other 
side.

Figure 23 - iNSTALL THe WArP BeAM CrANK HANDLe

cap nut

warp beam 

crank handle

3/8" washer

threaded  

shaft

slot in beater side

hole for 

beater pin 

to hold 

the beater 

upright

fold support bar

Summary of Contents for BABY WOLF LOOM














Reviews:

No comments