Schacht BABY WOLF LOOM Assembly Instructions Manual Download Page 10 | Manualshive

Page: 10 / 13

Schacht BABY WOLF LOOM Assembly Instructions Manual Download Page 10

- 10 -

15.

Install the upper rear castle cross brace.

Parts: Upper rear castle cross brace, 2 – #8 x 1-1/2” screws.

Orient the brace with the logo right side up. Attach the rear
upper castle cross brace to the castle with a 1-1/2" screw at
each end of the brace.

Figure 18 - iNSTALL THe WArP BeAM

threaded pin

through hole

in leg

short pin into

stopped hole

in leg

Figure 16 - iNSTALL THe uPPer reAr CASTLe CrOSS BrACe

upper rear castle cross brace

1-1/2" screw

1-1/2" screw

rear castle

cross brace

Figure 17 - iNSTALL THe TreADLe AiD

1-1/4" screw

1/4" dowel

treadle aid

cord

treadle aid

bar

rear castle

cross brace

Install the Treadle Aid (8-Shaft and 4Now/4Later
Looms only).

Parts: 2 – #8 x 1-1/4" screws, 1 – 1/4" dowel, 10 – treadle
aid cords.

Attach the treadle aid bar to the rear castle cross brace
with a 1-1/4" screw at each end. To set up the treadle aid,
start at one end of the treadle aid bar and push a treadle
aid cord up through one of the holes (an opened paper clip
can be most helpful with this step) and then over the 1/4"
dowel. Continue across the entire treadle aid bar. You will
attach the treadle aid cords to the ends of the treadles in
the same manner as you will attach the tie-up cords that
control the lamms (instruction 26). We recommend using a
treadle aid cord on all of the treadles.

16.

Install the warp beam.

Parts: Warp beam, 2 – 3/8" USS washers.

Take the warp beam and place a 3/8" USS washer on each
end. Slip the threaded rod through the hole in the inside
right leg as far as it will go. Fit the pin in the other end into
the stopped hole in the inside leg - this hole does not go all
the way through the leg. You will have to spread the right
and left inside legs apart to accomplish this.

14.

Insert the shafts into the castle.

Parts:
For 4-shaft looms: 4 small hex nuts, 4 small O-rings.
For 8-shaft looms: 8 small hex nuts, 8 small O-rings.

Slide a harness frame into the front channel in the castle
sides. Insert the jack pin into the hole in the center of the
bottom of the frame. Secure the jack pin with a hex nut,
then push a small O-ring on top of each hex nut. As you
insert the rest of the harnesses, keep them oriented so that
the heddle bar hooks are lined up.

Note: This process is covered in the video

Assembling the

Baby Wolf Loom

. You can find the video at youtube.com/

user/schachtspindle.

Figure 15 - SeCure THe JACK PiNS

heddle bar hook

hex nut with O-ring

on top

heddle bar

harness frame

jack pin (inside frame)

«
...
8
9
10
11
12
...
»

Summary of Contents for BABY WOLF LOOM














Reviews:

No comments