Schacht BABY WOLF LOOM Assembly Instructions Manual Download Page 1 | Manualshive

Page: 1 / 13

Schacht BABY WOLF LOOM Assembly Instructions Manual Download Page 1

- 1 -

Find out more at

schachtspindle.com

Schacht Spindle Company 6101 Ben Place Boulder, CO 80301
p. 303.442.3212 f. 303.447.9273

© 2017 Schacht Spindle Company, Inc.

04.17

BABY WOLF LOOM

A

ssembly

I

nstructIons

for

K

nocKed

-d

own

l

ooms

TOOLS

#2 Phillips screwdriver
5/16" or adjustable wrench
Flat screwdriver

HARDWARE LIST

Note: Parts pictures are not to scale. Listed part quantities

are what is needed for assembly. There may be extras of
some parts. Parts may not be pictured in every listed size.

HARDWARE BAG A

–

STEPS 1-3

4

–

Fold bars

4

–

3/16" x 1-1/4" carriage bolts

4

–

3/16" lock nuts

8

–

3/16" washers

2

–

1/4" washers

2

–

5/16" lock nuts

2

–

Black knobs w/ 1" threaded shaft

2

–

Plastic bearings

HARDWARE BAG B

–

STEPS 4-8

6

–

1/4" x 2" machine screws

6

–

1/4" barrel nuts

1 – Ratchet advance lever
2 – 3/8" USS washers
4

–

#8 x 1-1/2" screws

BEFORE YOU BEGIN

■

Please read through the directions before beginning to

assemble your loom.

■

Unpack the loom parts carefully. Do not throw away

the carton or any of the packing material until you have
checked to see that all of the parts and hardware have been
received

■

All hardware is sized in inches. Illustrations of the vari-

ous hardware and an inch scale are provided to aid you in
determining the correct piece of hardware to use.

■

Before starting the assembly, read the instructions com-

pletely and familiarize yourself with the drawings and parts.

■

Follow the exact order of assembly. Take care and work

slowly. If you have someone to help you, the assembly will
be easier.

■

The wood parts have a removable label on them to iden-

tify each part. We recommend that you leave the labels in
place until the loom is fully assembled.

■

When you finish assembling the Wolf loom, go back over

all of the screws and make sure they are tight. It is a good
idea to re-tighten the screws every few months. Remember
not to tighten those screws and bolts which are supposed
to allow their parts to pivot.

■

All wooden parts of the loom have been finely sanded

and finished with hand-rubbed Danish oil. From time to
time you may wish to apply more finish to the loom. Use a
Danish oil (tung oil and polyurethane mixture) and hand
rub the wood with a soft, lint-free cloth. Be sure to follow all
the manufacturer’s instructions.

Fold bar

Knob w/ 1" shaft

Plastic bearing

1-1/4" carriage bolt

Lock nut

2" machine screw

Barrel nut

1-1/2" machine screw

2-1/2" carriage bolt

Slim lock nut

Lock nut from top

Wing nut

Ratchet advance lever assembly

1-1/2" screw

1
2
3
...
»

Summary of Contents for BABY WOLF LOOM














Reviews:

No comments