background image

6 • 

E-649RA

 - User Manual

EN

FR

IT

STORAGE

COMPLETE TOOL EQUIPMENT

The pneumatic-hydraulic tool embedded in a shipping container must be stored in 
environment with relative humidity to 70% and temperature ranging from +5°C to +40°C, 
without aggressive evaporation of salts, acids and caustics.

3. GENERAL MAINTENANCE

General maintenance should be performed after about 500 000  
strokes or once every three years. The whole tool must be completelly disassembled and all seals 
and worn parts must be replaced. This repair may be carried out by an authorized technician only 
or a person trained by the manufacturer or supplier.

Replaceable nose-pieces located in a plastic reservoir (Ø4.8/5.0, 6.0 et 6.4), jaws set, Operations 
manual.

We recommend the customer to check completeness according the the above stated list (2. 
LIST OF QUICKLY EXPENDABLE PARTS).

SPARE PARTS

1. ORDERING

Order the spare parts exlusively from the manufacturer or from your sales agents.   

The order must contain:
a) tool serial number
b) number of ordered part
c) number of pieces
d) name of your company and precise address
e) your tax identification number and identification number  

2. LIST OF QUICKLY EXPENDABLE PARTS

Assembly:

Mount the parts (see par. disassembly) in a reverse order. On the 
outer surface of the jaws /fig.2 - pos.4/ apply a drop of lubricating 
oil ( we recommend hydraulic oil grade HLP ISO VG 32), apply 
thin layer of plastic lubricant MOGUL LV 2-3 to the suction 
pipe and «O» ring /fig.2 - pos.7,6/. Basic set-up of the jaws is 
performed as in fig. no. 3.

FIG.3

Designation

Reference

Nose-piece 5

E-NEZ-RA-50

Nose-piece 6

E-NEZ-RA-60

Nose-piece 6.4

E-NEZ-RA-64

Nose-piece 6.4 monobolt

D-1300165

Clamping sleeve

D-1300103

Designation

Reference

Set of jaws

S-1100153

Conduit suction

S-1300503

Scraper ring

D-1100301

Nut HP

D-1100401

Mandrel container

S-1301400

Summary of Contents for E-649RA





















Reviews: