Scantool MBR Manual Download Page 10 | Manualshive

Page: 10 / 23

background image

9

3.2 OPENING THE PACKAGE

If any visible damage exists on the machine when you receive the machine immediately
inform the dealer or manufacturer. Also never forget to state the visible damage on transport
documents.

The packing material is completely safe and do not consist any environmentally dangerous
articles. However they must be kept out of reach of children as some nylon products in
packing may cause suffocation if used as a toy etc.

3.3 SETTING UP

The machine can be bolted to the ground as shown below. The bolts must be tightly
screwed for the machine not to move under strain. Also check these bolts for breaking
periodically.

•

Please drill the ground about 100 mm long.

•

Please dean the ground.

•

Replace screws machine body to the ground carefully.

•

Please check the screws in the ground at every six months.

3.4 Foundation PLAN

«
...
8
9
10
11
12
...
»

Summary of Contents for MBR
























Reviews:

No comments

Related manuals for MBR

Brand: ACS Pages: 56

Brand: QBC Diagnostics Pages: 65

Brand: MAHA Pages: 21

Brand: MAGUIRE Pages: 47

Brand: GE Pages: 37

Brand: Parkside Pages: 88

DSO8000E Series

Brand: Hantek Pages: 95

Brand: Marcy Pages: 13

AudioBox 1818VSL

Brand: PRESONUS Pages: 80

Brand: Ikan Pages: 5

Brand: DeLaval Pages: 26

E-Boxx EV Simulator

Brand: Walther Pages: 12

GE cirrent Tetra Rigid Light Bar

Brand: Daintree Pages: 9

Brand: Master Pages: 80

Brand: Southwire Pages: 15

Brand: Interacoustics Pages: 2

Brand: Buyers Pages: 2

Brand: Drive Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands