Scanjet SC 40RT Instruction Manual Download Page 36

Page: 36 / 44

#SC 40RT 06 – 101027

Page 36 of 44

16. Basic Settings

This lists serves as guidance for ordering spare parts depending on the number
and size of the nozzles on the machine. This list may be changed without prior
notice.

Nozzle size 2 x Ø6 mm

Pos.

Part No.

Qty.

Description

110

21013-28

Turbine T2 Ø28

111

30024-28

Turbine Cone Ø28

136

20005-1

Adjusting Sleeve Assembly

143

802121-25

Nozzle Housing 2N

145

70011

Nut

146

50158

Flow Guide

147

50156-100-L

Nozzle Tube

148

105087

Bolt

149

50155-06

Nozzle Ø6 mm

Nozzle size 2 x Ø7 mm

Pos.

Part No.

Qty.

Description

110

21013-38

Turbine T2 Ø38

111

30024-38

Turbine Cone Ø38

136

20005-1

Adjusting Sleeve Assembly

143

802121-25

Nozzle Housing 2N

145

70011

Nut

146

50158

Flow Guide

147

50156-100-L

Nozzle Tube

148

105087

Bolt

149

50155-07

Nozzle Ø7 mm

Summary of Contents for SC 40RT













































Search results

Summary of Contents for SC 40RT

Reviews:

Related manuals for SC 40RT

Brands by name

Popular brands

Scanjet SC 40RT, Instruction Manual

Search results

Summary of Contents for SC 40RT

Reviews:

Related manuals for SC 40RT

Brands by name

Popular brands