2 Wash the arms in soapy and warm water and use a soft brush
to clean the jets. Replace them after rinsing them thoroughly.
Caring For The Dishwasher
Frost precaution
Please take frost protection measures on the dishwasher in win-
ter. Every after washing cycles, please operate as follows:
1. Cut off the electrical power to the dishwasher at the supply
source.
2. Turn off the water supply and disconnect the water inlet
pipe from the water valve.
3. Drain the water from the inlet pipe and water valve. (Use a
pan to gather the water)
4. Reconnect the water inlet pipe to the water valve.
5. Remove the filter at the bottom of the tub and use a sponge
to soak up water in the sump.
After every
wash
After every wash, turn off the water supply to the appliance and
leave the door slightly open so that moisture and odors are not
trapped inside.
Remove the plug
Before cleaning or performing maintenance, always remove the
plug from the socket.
No solvents or abrasive cleaning
To clean the exterior and rubber parts of the dishwasher, do not
use solvents or abrasive cleaning products. Only use a cloth with
warm soapy water.
To remove spots or stains from the surface of the interior, use a
cloth dampened with water an a little vinegar, or a cleaning
product made specifically for dishwashers.
When not in use for a longtime
It is recommend that you run a wash cycle with the dishwasher
empty and then remove the plug from the socket, turn off the
water supply and leave the door of the appliance slightly open.
This will help the door seals to last longer and prevent odors
from forming within the appliance.
Moving the appliance
If the appliance must be moved, try to keep it in the vertical posi-
tion. If absolutely necessary, it can be positioned on its back.
Seals
One of the factors that cause odours to form in the dishwasher is
food that remains trapped in the seals. Periodic cleaning with a
damp sponge will prevent this from occurring.
INSTALLATION INSTRUCTION
WARNING
Electrical Shock Hazard Disconnect electrical power before in-
stalling dishwasher.
Failure to do so could result in death or electrical shock.
Attention
The installation of the pipes and electrical equipments should be
done by professionals.
WARNING
For personal safety:
• Do not use an extension cord or an adapter plug with this
appliance.
• Do not, under any circumstances, cut or remove the earthing
connection from the power cord.
Electrical requirements
Please look at the rating label to know the rating voltage and
connect the dishwasher to the appropriate power supply. Use
the required fuse 10A/13A/16A, time delay fuse or circuit break-
er recommended and provide separate circuit serving only this
appliance.
Electrical connection
Ensure the voltage and frequency of the power being corre-
sponds to those on the rating plate. Only insert the plug into an
electrical socket which is earthed properly. If the electrical socket
to which the appliance must be connected is not appropriate for
the plug, replace the socket, rather than using a adaptors or the
like as they could cause overheating and burns.
Ensure that proper earthing exists before use
Water Supply And Drain
Cold water connection Connect the cold water supply hose to a
threaded 3/4 (inch) connector and make sure that it is fastened
tightly in place.
If the water pipes are new or have not been used for an extend-
ed period of time, let the water run to make sure that the water
is clear. This precaution is needed to avoid the risk of the water
inlet to be blocked and damage the appliance.
About the safety supply hose
The safety supply hose consists of the double walls. The hose’s
system guarantees its intervention by blocking the flow of water
in case of the supply hose breaking and when the air space be-
tween the supply hose itself and the outer corrugated hose is full
of water.
WARNING
A hose that attaches to a sink spray can burst if it is installed on
the same water line as the dishwasher. If your sink has one, it is
recommended thet the hose be disconnected and the hole
plugged.
How to connect the safety supply hose
1. Pull The safety supply hoses completely out from storage
compartment located at rear of dishwasher.
2. Tighter the screws of the safety supply hose to the faucet
with thread 3/4inch.
3. Turn water fully on before starting the dishwasher.
How to disconnect the safety supply hose
1. Turn off the water.
2. Unscrew the safety supply hose from the faucet.
