![background image](http://html.mh-extra.com/html/scandomestic/high-cube/high-cube_user-manuel_1206496007.webp)
7
REVERSING THE DOOR HINGE
The door can be opened from left to right and vice versa.
Should you wish to change the opening direction, please fol-
low these instructions.
Note: all parts removed should be kept safely. You will require
these for the reinstallation of the door.
• Remove the two screws (1) that hold the upper hinge
(5)(right side) to the frame.
• Lift the door off and place on a padded surface to prevent
scratching.
• Remove the blanking plug (8) from the hole in the upper
left corner of the door and transfer it to the uncovered
hole on the upper right corner. Press firmly to secure it.
• Remove the two screws (6) that hold the lower hinge (2)
• Remove the adjustable front left foot and transfer it to the
other side.
• Remove the bolt pin(7) from the lower hinge (2) and re-
verse the direction of the lower hinge. Secure the lower
hinge (2) to the left side of the lower frame with the two
screws (6) Re-insert the bolt pin (7). Set the door into po-
sition, making sure it is seated comfortably onto the lower
hinge (2).
• Holding the door closed, secure the upper hinge (5) into
the top frame with the two screws (1). Check the door is
level and tighten the screws firmly.
Fig 1 Position of components prior to reversal of the door
hinge.
Fig 2 Position of components after reversal of the door hinge.
BEFORE USING FOR THE FIRST TIME
• The appliance may be placed with its rear panel at a dis-
tance of at least 10 cm away from the wall to allow air cir-
culation.
• Your HighCube should be placed on flat and firm surface
for quieter operation.
• Do not expose the appliance to direct sunlight or a heat
source such as ovens, radiators, heaters, etc.
• Do not under any circumstances place heated beverages in
your HighCube.
• Do not open the door more often than necessary to lessen
the escape of cold air.
• For better air circulation, do not overfill the unit.
• Adjust the temperature regulator according to the amount
of product and the ambient temperature.
BASIC OPERATION
Your HighCube must stand on an even surface. If the appliance
is to be placed on carpet or delicate floors, support it with a
wooden board underneath. Be aware that placing the appli-
ance on carpet may mean that heat from the compressor may
cause the carpet to fade. Be aware that humidity can cause
water damage.
1. Clean the inner compartment.
2. Plug in your HighCube.
3. The first time you turn the unit on, set the thermostat, sit-
uated at the back of the unit, to the max. position “5”.
4. After 20 minutes, adjust the temperature control setting to
“3”. This setting should be correct for home use.
5. To turn the unit off, disconnect the plug from the mains
supply.
NOTE:
If the unit is unplugged or power lost, you must
wait 3 to 5 minutes before restarting. If you attempt to
restart the unit before this delay, the unit will not start.
Tips for Refrigeration
Adjust the internal temperature according to the amount of
product and the ambient temperature:
• Winter – Setting 1-2 (5°C-10°C)
•
Spring and Autumn – Setting 2-4 (10°C-15°C)
• Summer – Setting 4-5 (15°C-25°C)
The inner temperature varies in different parts of the cooler.
The back of the HighCube is coldest.
WARNING
If temperature selector is set to too low a setting, drinks be-
come frozen. In extreme circumstances, glass bottles may
even break. Always exercise caution when setting the temper-
ature.
• Do not place heavy items (more than 20kg) on top of the
HighCube.
• Do not place any items on top of the HighCube which may
fall off when the door is opened.
• After the appliance has been unplugged, leave for three
minutes before plugging it in again.
When not in use
If the unit is not being used for long periods: