13
INSTALLATION
Location
When selecting a position for your Fridge/Freezer you should
make sure the floor is flat and firm, and the room is well venti-
lated with an average room temperature of between 16
℃
and
43
℃
. Avoid locating your Fridge/Freezer near a heat source, eg,
cooker, boiler or radiator. Also avoid direct sunlight in out-
buildings or sun lounges. If you are placing your Fridge/Freezer in
an out-building such as a garage or annex ensure that the
Fridge/Freezer is placed above the damp course, otherwise con-
densation will occur on the Fridge/Freezer cabinet. Never place
the Fridge/Freezer in a wall recessed or into fitted cabinets or
fumiture when your Fridge/Freezer is working, the grille at the
back may become hot and the sides warm. It must therefore be
installed so that the back of the Fridge/Freezer has at least
9cm(31/2”) of free space and the sides have 2cm(3/4”). Do not
drape the Fridge/Freezer with any covering.
Leveling the Fridge/Freezer
If the Fridge/Freezer is not level, the door and magnetic seal
alignment will be affected and may cause you Fridge/Freezer to
work incorrectly. Once the Fridge/Freezer is placed in its final lo-
cation, adjust the leveling feet at the front by turning them.
Cleaning before use
Wipe the inside of the Fridge/Freezer with a weak solution of bi-
carbonate of soda. Then rinse with warm water using a damp
sponge or cloth. Wash the baskets and shelves in warm soapy
water and dry completely before replacing in the Fridge/Freezer.
The external parts of the Fridge/Freezer can be cleaned with wax
polish.
Before plugging in YOU MUST
Check that you have a socket which is compatible with the plug
supplied with the Fridge/Freezer. If not see the section called
ELECTRICAL INFORMATION
Before switching on!
DO NOT SWITCH ON UNTIL FOUR HOURS AFTER MOVING THE
FRIDGE/FREEZER.
The coolant fluid needs time to settle. If the appliance is
switched off at any time, wait 30 minutes before switching back
on to allow the coolant fluid to settle.
Before filling your Fridge/Freezer
Before storing foods in your Fridge/Freezer, turn the
Fridge/Freezer on and wait for 24 hours, to make sure it is work-
ing properly and to allow the Fridge/Freezer to fail to the correct
temperature.
START Testing
1. Clean the parts of the refrigerator with lu-
kewarm water containing a littleneutral
detergent and with clear water, and wipe
them dry.
Notes: Electric parts of the refrigerator can
only be wiped by dry cloth.
2 Turn on electricity. The compressor begin
to work.
3. Open the door 30 minutes later, if the
temperature in the refrigerator decreased
obviously, it shows that the refrigerator
system works well. When the refrigerator
operates for a period of time, the tem-
perature controller will automatically set
the temperature within limits it opens.
The display is located in the middle of the re-
frigerator door. Please refer to the below figure
for the layout.
Introduction of the buttons
1 Fridge: to set the refrigerator temperature
2 Freezer: to set the freezer temperature
3 Function: to choose functions of fast cooling, fast freezing,
intelligence and vacation
4 OK: to enter or to quit the existing function setting
Appliance connected to power at the first time
When the appliance is connected to power at the first time, the
display will be lit for 2 seconds beforegoing normal and the ap-
pliance runs with intelligence function.
Display control
When the refrigerator door is closedand there is no button oper-
ation in 3 minutes, the display light goes off.
When the display light is off, open the refrigerator door or click
any button to light it up.
Temperature setting
1 Click the “refrigerator” or “freezer” button and when it flic-
kers in the symbol, temperatures can be set; each time
when the button is clicked, the temperature changes accor-
dingly (the display shows the temperature accordingly).
(Temperatures cannot be set under functions of fast cooling,
fast freezing, intelligence and vacation,)
2 Under temperature setting, if there is no button operation in
5 seconds, the button stops flickering and the set tempera-
ture comes into effect.
3 )Temperature cycle
Refrigerator:
2°C →3°C →4°C →5°C →6°C →7°C →8°C →OFF →2°C
；
Freezer:
-24°C →-23°C →-22°C →-21°C →-20°C →-19°C →-18°C →-
17°C →-16°C →-24°C
；
Intelligence
Under intelligence, it is 4°C in the refrigerator and -18°C in the
freezer.
Temperatures cannot be changed and you can click the tempera-
ture zone button to check the temperature.
To enter intellegence
Click
“option”
until it flickers and then click
“OK”
to enter this
function.
To quit intellegence
Under intelligence, click
“option”
until it goes to intelligence,
click
“OK”
to quit this function and the light goes off.
Temperatures of each chamber go back to the value beforeintel-
ligence function.
Fast cooling
Under fast cooling, it is 2°C in the refrigerator and the refrigera-
tor temperature cannot be changed.
To enter fast cooling
Click “option” until it flickers in “fast cooling” and then click “OK”
to enter this function.
To quit fast cooling
Under fast cooling, click “option” until it goes to “fast cooling”
and then click “OK” to quit this function.
