background image

26

R

Section 6

6.1 TRAVEL ADJUSTMENTS

Neutral or tracking adjustments will need to be made if:

A.  The  steering  control  levers  are  in  the  neutral 
position and the machine creeps forward or backward. 
See Neutral Adjustment (next procedure).

B.  The steering control levers are in the full forward 
position and the mower pulls to one side or the other 
when  traveling  in  a  forward  direction.  See Tracking 
Adjustment on page 27.

NEUTRAL ADJUSTMENT

1.  Be sure the dump valve levers are in the run position 

and the steering control levers are in the neutral lock 
position.

2.  With an operator in the seat, start the engine and 

disengage the parking brake.

3.  Run the engine at full operating speed and check if 

the machine creeps forward or backwards.

4.  Adjust the RH wheel by loosening the jam nuts on 

the steering control rod and turning the rod until the 
drive wheel turns in the forward direction. Turn the 
rod back until the drive wheel stops moving. Turn the 
rod an additional 1/2 turn. See Figure 6-3.

390S0149-1

CONTROL

ROD

LOOSEN

HERE

STT99RHCRA

LOOSEN HERE

ADJUST HERE

Figure 6-3. RH Steering Control Rod Adjustment

5.  Tighten the jam nuts and repeat for the LH wheel. 

See Figure 6-4.

390S0147-1

LOOSEN

HERE

390S0146

LOOSEN HERE

ADJUST HERE

Figure 6-4. LH Steering Control Rod Adjustment

Summary of Contents for STTII-52V-26CH-EFI


























































































Reviews: