SBG Navsight Apogee IMU Hardware Manual Download Page 61

Page: 61 / 74

Navsight Solution

– Hardware Manual

NAVSIGHTHM.1.3

7.7.7. CA-NAVS-SPLIT-COM-0.5M

This cable is designed for easy external GNSS integration, thanks to
dedicated RS-232/RS-422 serial connector and a PPS input connector.
General characteristics are the following

●

1 x ODU Mini-Snap F Series S31F1C-P08MFG0-5500 plug

●

1x Male DB-9 plug

●

1x BNC plug for PPS input (SYNC IN)

●

IP-68 rating

●

50cm long

Cable wiring depends on the port on which user will connect the cable and is as follows

Pin on DB-9 plug

PORT A

PORT B/C/D/E

PORT A RX

PORT # RX / RX+

PORT A TX

PORT # TX / TX-

SYNC OUT A

SGND

RX-

TX+

Note: This cable is included in the rugged processing unit package in its external GNSS version (-E).

It can also be ordered separately.

61/74

Figure 7.12 : Spliter cable

adapter

Summary of Contents for Navsight Apogee IMU











































































Search results

Summary of Contents for Navsight Apogee IMU

Reviews:

Related manuals for Navsight Apogee IMU

Brands by name

Popular brands

SBG Navsight Apogee IMU, Hardware Manual

Search results

Summary of Contents for Navsight Apogee IMU

Reviews:

Related manuals for Navsight Apogee IMU

Brands by name

Popular brands