manualshive.com logo in svg

SB SB-SP7200-GSM, Instruction Manual

Share
Download
SB SB-SP7200-GSM Instruction Manual Download Page 8

Page 8

All-In-One GSM Home Alarm & Video System

Product Manual : SB-SP7200-GSM

www.SafetyBasement.com     Phone: 877-345-2336   Fax: 888-236-2524

POWER & CELLULAR SIGNAL

Insert the power adapter plug into the Main Unit.

The Charging Light should be RED. It will remain red for some 

time until the backup battery is fully charged.

Turn the Main Unit ON.

Look at the Status Light under the Camera Lense.

Shortly, the Status Light will blink 3 times, every 2.5 seconds. 

This means that the Main Unit has found a cellular signal and is 

working properly.

If the status light does not blink like this within 2 minutes, 

turn off the unit and check the installation of your SD and SIM 

Cards.

Try again. If the unit does not blink 3 times, every 2.5 seconds, 

try moving the unit to an area where there may be a better 

signal.

Try moving on to the next step of this setup to see if you are 

connected.

If you are unable to connect, you should check to make 

sure your SIM Card has been properly activated. Contact 

SafetyBasement or your cellular provider.

STATUS LIGHT

Summary of Contents for SB-SP7200-GSM
































Reviews:

No comments

Brands by name

Popular brands

Load more brands