manualshive.com logo in svg

SB SB-SP7200-GSM, Instruction Manual

Share
Download
SB SB-SP7200-GSM Instruction Manual Download Page 5

Page 5

All-In-One GSM Home Alarm & Video System

Product Manual : SB-SP7200-GSM

www.SafetyBasement.com     Phone: 877-345-2336   Fax: 888-236-2524

Your GSM Alarm System uses text messages to communicate with you. This requires sending 

the unit particular codes. We have put together a list of codes at the end of this manual, but for 

now, please follow the instructions in order so that you may best understand how the system 

works.

REQUIREMENTS:

You should have the following for proper operation of your GSM Alarm System.

1) Your GSM Alarm System, with the Main Unit, Remote Control, Sensors, a Power Adapter, 

USB Cable and mounting accessories.

2) A micro SD Card, up to 32GB. You can order a compatible card from SafetyBasement.com. 

Should you already have an SD card, please be sure it has been erased.

3) A cellular SIM card. A compatible card is available from SafetyBasement.com. Please check 

with SafetyBasement for SIM card requirement before using another card. ANY SIM card will 

require a monthly fee.

4) A small Phillips head screwdriver.

5) 3 AAA batteries for wireless PIR unit.

INTRODUCTION

Summary of Contents for SB-SP7200-GSM
































Reviews:

No comments

Brands by name

Popular brands

Load more brands