Warning
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building Regulations.
Check the pack and make sure you have all of the parts listed.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot
restore the electrical supply without your knowledge.
If replacing an existing fitting, make a careful note of the connections.
This light fitting should be connected to a circuit with a 30mA RCD fitted.s.
An appropriate outdoor mains cable must be used to power this product.
This product is desinged to be fitted horizontally and vertically in decking,walls, steps, and suitable for installation dierctly
into the ground.
Never cover the product.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
This product is not suitable for location in or near a marine environment.
This product is unsuitable for immersion in water.
Rated maximum surface temperature is 140 ºC.
This luminaire with type Z attachment, for type Z attachments: the external flexible cable or cord of this luminaire cannot be
replaced; if the cord is damaged, the luminaire shall be destroyed.
The resistant to static loads is 5KN. This product is not suitable for drive-over, carriageways, parkings, etc.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
Thank you for purchasing this light fitting. Please read the instruction carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instruction for future reference.
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting,
carefully
note the position of each set of wires.
Note that the switch is turned off before installation.
After deciding the layout of the light fitting/s, and the position of the junction box, ensure the cables are long enough to the
desired positions.
The power supply is Double Insulated and
does not require connection to an Earth circuit.
Layout
Plan the desired layout of these fittings carefully, ensuring the cables will reach the distances between the junction box and the
each LED light fitting.
Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction boxes
(not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
An appropriate outdoor mains cable must be used to power this product. We recommend that you use H05RN-F specification
cable (not supplied) which is an outdoor grade, rubber sheathed cable.
The mains supply cable must have a minimum cross section area of 1.0mm
2
.
Cables must be protected using suitable conduit or plastic trunking.
Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.
•
Used as a deck light.
See Fig 1
. Carefully pull the product out of plastic housing. Select a mounting location for the
product and prepare a cut out size of
D36 x 50mm
.
•
Used as a ground light
. This product must be fitted into the supplied housing and then installed into concrete or paving
slab. It must not be installed into soil.
See Fig 2
. Select a mounting location for the product and prepare a cut out size of
D39 x 90mm
.
• Replace fuse or circuit breaker and switch on. Your light is now ready for use.
• Form a recess to fit the housing into. The dimensions of the housing are 39mm diameter with 90mm minimum ground void.
Ensure that there is adequate drainage below the product.
• It is recommended to cut the hole slightly smaller than needed, then file the hole until the recessed unit fits snugly.
• Ensure that there is some slack cable to allow removal of the unit.
• Push the unit into the hole, and adjust the cable so it does not get snagged.
Deck cut out size: Dia 36mm
Mininium deep: 50mm
LED head unit
1
.5
m
Supplied housing
Deck cut out size:
Dia 39 x 90mm
Supplied housing
for ground fitting
LED head unit
1.5m
Fig 1.
Fig 2.
Deck fitting
Ground fitting
Walkway use only
• Ensure that adequate room is left for the cable.
• Feed the cable of each unit through the mounting holes and check the fit of the unit in the hole.
