Warning
Please read these instructions carefully before commencing any work
This Emergency pack must be fitted by a competent and qualified electrician.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
Please Note:
The limited warranty shall be deemed null and void in the following circumstances: Failure by the installer, end
user or any third party to exercise caution to protect any covered product or part from outside damage, adverse temperature
(normal operating ambient temperature 0 - 25°C), humidity conditions, fluctuations in the electrical system or physical abuse
as well as failure related to workmanship in the installation of the products or parts.
These products are designed for connection to a 220-240V~50Hz supply.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or maintaining this fitting. Ensure other persons
cannot restore the electrical supply without your knowledge.
This Emergency pack is suitable for indoor use only.
If replacing an existing fitting, make a careful note of the connections.
Do not use Megger or similar high voltage instruments. Due to the fact this Emergency pack contains electronic components
that maybe damaged by high test voltages, they must be disconnected from the circuit before testing.
To prevent damage to the Emergency pack, do not mix with conventional magnetic ballasts on the same electrical circuit.
Any faulty, broken or damaged modules should be replaced immediately.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
This light fitting is double insulated and does
not require connection to an Earth circuit.
Check that...
• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the connection block.
Familiarize yourself with the installation procedure and ensure the power is safely isolated before installing the Emergency pack.
Ensure the LED luminaire is within the specification 9-80VDC.
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully
note the position of each set of wires.
Note that the switch is turned off before installation.
Wire as required below (Fig.1):
Non-Maintained Emergency:
Connect the mains input Unswitched Live (
PL
), Neutral (
N
). The low voltage side just requires output to the LED luminaire
positive (
+
) and negative (
-
). Then connect the battery. Install the LED indicators in a suitable location.
Maintained Emergency:
Connect the mains input Unswitched Live
(PL
), Neutral (
N
) and Switch Live (
SL
). Connect the Live out (
L
D
) and Neutral out
(
N
D
) to the driver mains input. The low voltage side connect the output from the LED driver to the LED Driver output (
+
) and
Negative (
-
) luminaire output to the output to LEDs positive (
+
) and negative (
-
). Then connect the battery. Install the LED
indicators in a suitable location.
Please note: For manual testing purposes a provision is made inside the cover of the low voltage side of the driver
(Fig.1) marked as Test on the casing. See overleaf for details on manual testing.
Turn on the power and ensure that the module is showing charge indicator.
This fitting requires a minimum 24 hours initial charge period prior to any manual emergency testing.
The battery has a rated duration of at least 4
years but should be replaced if the duration
of operation is less than 3 hours after a 24hr
charge time with no interrupted supply.
All full duration tests should be where
possible be undertaken at times of low risk
adjacent emergency luminaires we
recommend that you you reset the inbuilt
timer or run a manual 30 day test to stagger
testing times. Once commissioned fill in the
date of the first test/install date this will
allow the end user to monitor and record
subsequent test information on the supplied
report. All tests with the exception of the
visual inspection will be completed
automatically including battery charge
condition and lamp status.
L
N
N
SL
PL
BAT -
BAT +
Test
G+
G-
R+
R-
+
-
+
-
Output to LEDs
LED Driver output
Output to LED
Luminaire
N
L
-
+
Output to LED
LED Driver
240VAC Input
Input from mains
supply
Battery connector
Red/Green Status LED
Maintained Emergency optional wiring
Manual Test Button
D
D
Daily:
The battery in this product has self testing
function. Visual inspection of the battery
charge LED as below:
Automatic Monthly (Every 30 Days):
(in addition to the daily check)The results of
the short duration test shall be recorded.
Automatic Annually (Every 180 & 360
Days):
(in addition to the daily check)
The results of the full duration tests shall
be recorded.
Manual Testing -
Can only be completed under mains conditions
Manual Simulated Power Failure
Manual 30 Day Test
Manual 180/360 Day Test
Manual Fast Test (24 minutes)
Hold test button until you hear 1 beep
Hold test button until you hear 2 beeps
Hold test button until you hear 3 beeps
Hold test button until you hear 4 beeps
Abort Test
Hold the test button for 15 seconds, when you
hear the long sound, the self-test function will
restore the defaults
Fault Indicators:
Red LED flashing once a second, Green LED off,
Beeps twice every minute until fault rectified
Red LED flashing twice a second, Green LED off,
Beeps twice every minute until fault rectified
Battery/Charging Fault
Lamp Fault
Failed Duration Test
Red LED solid, Green LED off, Beeps twice every
minute until fault rectified
Performance Indicators:
Normal Operation
Automatic 30 Day Test
Automatic 180/360 Day Test
Manual Simulated Power Failure
Manual 30 Day Test
Manual 180/360 Day Test
Manual Fast Test (24 minutes)
Red LED off, Green LED Solid
Red LED off, Green LED flashing once a second
Red LED off, Green LED flashing twice a second
Red LED off, Green LED off
Red LED off, Green LED four times a second
Red LED off, Green LED flashing once a second
Red LED off, Green LED flashing twice a second
