Savoy House MONTECELLO Owner'S Manual Download Page 8

Page: 8 / 11

9. ATTACHING THE FAN

BLADES

Caution:

Remove the screws from the

motor support plate, discard the screws
and motor support plate.

Step 1.

Attach the blade to the blade

bracket using the screws and rubber
washers as shown in Figure 14. Start
screw into bracket. Repeat for the two
remaining screws.

Step 2.

Tighten each screw. Make sure

the blade is straight.

Step 3.

Fasten blade assembly to motor

using the screws supplied. (Fig. 14)

Figure 14

Figure 15

10. INSTALLATING THE

MOUNTING PLATE

1. Remove the 1 of 3 screws from the

mounting ring and loosen the other 2
screws. (Do not remove)

2. Place the key holes on the mounting

plate over the 2 screws previously
loosened from the mounting ring, turn
mounting plate until it locks in place at
the narrow section of the key holes.
Secure by tightening the 2 screws
previously loosened and the one
previously removed. (Figure 15)

Screws

Motor support
plate

Blade

Set of blades bracket

Screws

Rubber

washers

Screws

Mounting
plate

Mounting ring

Summary of Contents for MONTECELLO












Search results

Summary of Contents for MONTECELLO

Reviews:

Related manuals for MONTECELLO

Brands by name

Popular brands

Savoy House MONTECELLO, Owner'S Manual

Search results

Summary of Contents for MONTECELLO

Reviews:

Related manuals for MONTECELLO

Brands by name

Popular brands