background image

8

Figure 16

Figure 17

Figure 18

11. INSTALLING THE 

LIGHT KIT 

NOTE:

 Before starting installation, discon-

nect the power by turning off the circuit 
breaker or removing the fuse at fuse box. 
Turning power off using the fan switch is 
not sufficient to prevent electric shock.

Step 1.

 Remove the 1 of 3 screws from the 

mounting plate and keep it for future use. 
Loosen the other 2 screws (Do not 
remove)

Step 2.

 Raise and hold the light kit close to 

the mounting plate and proceed to do the 
wire connections. Connect the white wire 
connectors from the light kit and fan, 
follow the same procedure with the black 
wire connectors. (Fig. 16) 

Step 3.

 Tuck connections neatly into 

mounting plate, Place the light plate key 
holes over the 2 screws previously 
loosened from the mounting ring, turn 
light kit until it locks in place at the narrow 
section of the key holes. Secure by 
tightening the 2 screws previously 
loosened and the one previously removed. 
(Fig. 16)

12. INSTALLIN THE GLASS 

SHADE & LIGHT BULBS

Step 1.

 Install 3 x 60W candelabra bulbs 

(included). (Fig. 17)

Step 2.

 Mount the glass shade to the 

mounting plate by unscrewing partway 
the thumbscrews on the glass holder, 
insert the glass, then gently tighten the 
thumbscrews by hand evenly to the glass. 
DO NOT OVER TIGHTEN. (Fig. 17)

Step 3.

 Raise the glass frame up against 

the mounting plate and secure by 
tightening with the four glass frame 
screws. (Fig. 17)

NOTE:

 When installing the glass frame 

onto the mounting plate, be sure the 
arrow markings are aligned. (Fig. 18)

Bulbs

Glass 
shade

Glass 
frame

Mounting 
plate

Mounting 
plate

Connection plugs

Light kit

Screws

Thumb 
Screws

Arrow

Screws

Arrow

Summary of Contents for 56-578-5SV-SN













Reviews: