background image

 

INSTALLATION INSTRUCTIONS 

FOR 

DUCTED WHOLE HOUSE FANS 

 

 

Fan Models: CX1401, CX1801 

Read all warnings and instructions before beginning to install this fan.

 

WARNING

 – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO 

PERSONS, OBSERVE THE FOLLOWING: 

a)

 

Installation work and electrical wiring must be done by qualified person(s) in accordance with all 
applicable codes and standards, including fire-rated construction. 

b)

 

Sufficient air is needed for proper combustion and exhausting of gases through the flue 
(chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment 
manufacturer’s guideline and safety standards such as those published by the National Fire 
Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air 
Conditioning Engineers (ASHRAE), and the local code authorities. 

c)

 

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden 
utilities. 

d)

 

WARNING

 – 

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS 

FAN WITH ANY SOLID-STATE SPEED CONTROL DEVICE.

 

e)

 

Use this unit only in the manner intended by the manufacturer. If you have questions, contact the 
manufacturer. 

f)

 

Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting 
means to prevent power from being switched on accidentally. When the service disconnecting means 
cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. 
 

CAUTION 

 

DOUBLE CHECK FAN BLADES ARE SECURE TO HUB PRIOR TO INSTALLATION. 

BLADES CAN BE DAMAGED DURING SHIPMENT AND CAN BECOME A HAZARD 

UPON ACTIVATION OF MOTOR!

 

 

 

1.

 

This unit has an unguarded propeller. Do not use in locations readily accessible to people or animals. 

2.

 

For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. 

3.

 

Carbon monoxide is an odorless, colorless gas that can kill. It may be drawn into the house by operating 
this fan if your fuel-burning equipment is not properly maintained, or if you lack adequate attic space.

 

 

 

Summary of Contents for CX1401











Reviews: