This Quick Reference Guide provides all the steps necessary to install the SSA-4012-
xx. The SSA-4012 is a 6 x 12 audio matrix switcher and controller in a 1U rack-
mountable design.
Box Contents
(1) SSA-4012-xx unit
(1) Installation Kit (075-0144-xx)
(2) 1U Rack Mounting Brackets (071-0603-xx)
(4) Phillips Screws for Brackets (M3 x 8MM Flat) (039-0017-xx)
(2) 6-Pin Screw Down Plug in Connector (028-9352-xx)
(1) Power cord C13
(6 feet) (N. America) (064-0079-xx) or appropriate international power cord
(1) Quick Reference Guide (this document)
Required System Component
(1) Savant Smart Host or Savant Pro Host
Specifications
Environmental
Environmental
Temperature
32° to 104° F (0° to 40° C)
Humidity
10% to 90% Relative Humidity (non-
condensing)
Cooling
3 cubic feet per minute (CFM) recommended.
Maximum BTUs
61 BTUs per hour
Dimensions and Weight
Dimensions and Weight
Height
1.71 in (4.34 cm)
Width
17.30 in (43.94 cm)
Depth
8.69 in (22.08 cm)
Weight
Net: 5.25 lb (2.38 kg)
Shipping: 7.8 lb (3.54 kg)
Rack Space
1U
Power
Power
Input Power
100-240V AC, 50/60 Hz, (1.8 Amp maximum)
Nominal Power
12 watt
Maximum Power
18 watt
Stereo Preamp Parameters
Stereo Preamp Parameters
Total Harmonic DisNoise
(THD+N)
<0.005%, 20Hz - 20KHz, -100dB@1kHz
Dynamic Range
115dB
Signal-to-Noise Ratio (SNR)
>105dB
Frequency Response
20Hz - 20kHz +0dB +/-0.1dB
Output Impedance
50 ohms
Crosstalk
<-80dB
Supported Sample Rates
44.1 kHz/48 kHz/96 kHz/192 kHz at 16-bit or
24-bit resolution
Compliance
Compliance
Safety and Emissions
FCC Part 15 | S Mark | CE Mark | C-Tick
RoHS
Compliant
Minimum Support Release
Minimum Support Release
Savant OS
da Vinci 6.0.1
Front Panel
1
Reset button
(hole)
Resets Static IP address. Insert pin into hole for 5 seconds
to reset.
2
Power Bi-color
LED
Green
indicates the system has adequate power and is
operating normally.
Red
indicates the system is in standby mode. In standby
most of the Controller circuitry is powered down.
Off
indicates that the system is getting no power.
3
Status Bi-color
LED
Green
indicates the Host has established communications
with the embedded system.
Green flashing
indicates the embedded system is ready
(running with DHCP IP address), but the Host has not
established communications with the embedded system.
Off
indicates the embedded processor is resetting or is
powered up; and is booting the embedded firmware.
Red
indicates the Host has determined the firmware needs
to be updated, but a problem occurred during the process
that will initiate a reset.
Red flashing
indicates the embedded firmware is running,
but has not received a DHCP IP Address.
Amber
indicates the Host is currently updating the
embedded firmware.
Amber
flashing
indicates the embedded system has a valid
link-local IP Address and is waiting to connect to the Host.
Hardware Failure
If the Controller has a hardware failure, the Status LED
indication will be interrupted every 3 seconds with a solid
red indication. For example, if the LED is flashing green
when a hardware failure occurs, the LED will flash green,
solid red, etc in 3 second intervals.
4
RS-232 LED
Green
indicates RS-232 serial port data activity.
Off
indicates no RS-232 serial port activity.
5
GPIO LED
Green
indicates GPIO port signal activity.
Off
indicates no GPIO port activity.
6
On/Off button
(hole)
Insert pin into hole for about 5 seconds to place in standby
mode. The Power LED turns red. Insert the pin again for
about 1 second to take system out of standby mode. The
I/O
power switch on the back of Controller must be On (
I
) to
enable this function. To turn the power off for the entire
system, use the switch on the rear panel.
7
HDMI LED
Green
indicates the external host is connected to the
Host HDMI port.
Off
indicates the external host is not connected to the
Host HDMI port.
8
IR LED
Green
indicates IR port signal activity.
Off
indicates no IR port activity.
Rear Panel
1
Ethernet
8-pin RJ-45 10/100 Base-T, auto-negotiating port with Link/
Activity LEDs:
See items 8 and 9 for LED operation.
2
RS-232/422/485
8-pin RJ-45 female: Used to transmit and receive serial
binary data from devices.
Ports 1 & 2 support CTS/RTS.
4
GPIO Input
When configured as an input, the port detects a voltage
present and can safely detect the presence of a voltage of
0-30V DC with a threshold of approximately 2.4V DC.
5
GPIO Output
When configured as an output, the port outputs a voltage
below 12V DC 150mA. Combined maximum current for all
GPIO outputs is 550mA and will shut down if an over-current
condition is detected.
4
Host HDMI
19-pin type A HDMI female digital video/audio input:
Supports HDMI, DVI/D (requires adapter-not included)
Limited to 185 MHz pixel clock. Used for receiving up to 4
PCM streams (iTunes®) from a Pro Host. This is not
available on the Smart Host.
5
Stereo In
RCA line-level analog audio inputs (4 Right & 4 Left)
6
Stereo Out
RCA line-level analog audio outputs (12 Right & 12 Left)
7
Fuse
100-240V, 2.5A—Fast acting fuse. This is field-replaceable.
8
Link/Activity LED
Green
indicates an Ethernet link has been established.
Green Flashing
indicates Ethernet activity.
Off
indicates an Ethernet link has not been established.
9
Ethernet Speed LED
Yellow
indicates an Ethernet connection speed of 100 Mbps.
Off indicates an Ethernet connection speed of 10 Mbps.
10
IR
6-Pin Screw Down Plug in Connector (3.81 mm): (5V tolerant
only)
Sends IR signals to control devices with an IR input or IR
receiver via an IR flasher.
for important precautions regarding IR
functionality before making any connections.
11
Digital Audio In
TosLink (Optical) digital audio inputs. (2)
12
I/O (On/Off switch)
On/Off switch
I (On):
Powers On the controller.
O (Off):
Powers Off the controller.
13
Input Power
100-240V AC, 50/60 Hz, 1.8 Amp
SSA-4012-00 | 009-1201-01 | 140707
Savant Confidential and Proprietary
1 of 2
SmartAudio 6 x 12 Audio Matrix
(SSA-4012)
Quick Reference Guide
Scan this QR code for additional
product information.
