sauter flexotron 400 Series Manual Download Page 19 | Manualshive

Page: 19 / 27

background image

SAUTER

flexotron®400 - RDT405

Display and encoder

P100012100

19

Calculated setpoint

In control mode 4, Pressure control with outdoor compensation, the controller
does not work towards a fixed setpoint value. Instead, it works towards a
calculated setpoint, which varies with the outdoor temperature. The calculated
setpoint is displayed by turning the knob clockwise when in the Base Display.

6.1.1

The 10-second level

This level is reached from the Base Display by pressing and holding the encoder
button for 10 seconds. The 10-second level holds all the configuration menus.
See chapter 8 Configuration.

The controller must display the Base Display when pressing the encoder knob
to reach the 10-second level.

6.1.2

Display symbols

«
...
17
18
19
20
21
...
»

Summary of Contents for flexotron 400 Series




























Reviews:

No comments

Related manuals for flexotron 400 Series

Brand: ABB Pages: 370

Brand: ABB Pages: 17

Brand: ABB Pages: 104

Brand: ABB Pages: 120

Brand: ABB Pages: 42

Brand: Tapeswitch Pages: 13

Brand: K1EL Pages: 46

Brand: ZIGBEE Pages: 5

REVOLUTION Pro Controller 2

Brand: Nacon Pages: 11

Brand: Nacon Pages: 18

Brand: Nacon Pages: 24

Brand: Nabco Pages: 35

Brand: National Instruments Pages: 40

Brand: National Instruments Pages: 28

Brand: National Instruments Pages: 7

Brand: National Instruments Pages: 22

Brand: Rain Bird Pages: 138

Brand: Watts Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands