Saunier Duval Thelia 30 E Installation And Operating Instructions Manual Download Page 3

3

INTRODUCTION

The 

THELIA 30 E 

boiler is a wall mounted combina-

tion boiler providing central heating and instanta-
neous hot water.

The boiler is of the 

II 2H3

 category for use with Natu-

ral Gas (G20) as distributed in the United Kingdom,
or Butane (G30), Propane (G31) or Towns gas
(G130).

Boilers burning LPG or similar gases MUST NOT be
fitted in basements or below ground level.

The boiler has a fan assisted balanced flue which
both discharges the products of combustion to and
draws the combustion air from the outside of the
room.
The boiler is suitable for top outlet flue connection
only but, can be fitted with horizontal flue, vertical
flue or twin-pipe flue. Refer to flue catalogue for
further details.

Both the central heating and domestic hot water
temperature are user adjustable from the boiler
control panel.

Hab 031a

Domestic hot water demand always has priority
over heating demand.
The boiler is designed for use as part of a sealed
water central heating system with fully pumped cir-
culation. The pump, expansion vessel and associ-
ated safety devices are all fitted within the boiler.

The boiler can be installed against either an exter-
nal wall or on an adjacent inside wall, that is, the
flue system will pass directly to the rear or to either
side to the terminal fitted on the outside wall face.

The installation must be carried out by a compe-
tent person in accordance with the relevant re-
quirements of The Building Regulations, The Water
Byelaws, The Building Standards (Scotland) Regu-
lations and any applicable local regulations.

These instructions should be carefully followed for
the safe and economical use of your boiler.

Ancillary equipment

A range of flue accessories are available includ-
ing vertical flues, twin-pipe flues, bends etc.
For further information contact your supplier.

COMMISSIONING

Gas safety (Installation and Use) Regulations
In your interests and that of gas safety, it is the law
that ALL gas appliances are installed and serviced
by a competent person in accordance with the
above regulations.

Gas leak or fault

If a gas leak or fault exists or is suspected, turn the
boiler off and consult the local gas supply com-
pany or your installation/service company.

Boiler controls

The control panel, located at the lower front of the
boiler casing, 

see diagram 1

, allows the boiler to

be started, shut down, controlled and monitored
during use.

Flue

Do not obstruct the outside terminal of the boiler.

Diagram 1

bar

0

A

B

C

D

E

F

G

H

I

J

K

L

G

 

-

N/A on this model

H

-

Safety shutdown warning light

I

-

Domestic hot water temperature control

J

-

Heating temperature control

K

-

'Summer/winter' selector

L

-

N/A on this model

A

-

Pressure gauge

B

-

Temperature gauge

C

-

Reset button

D

-

N/A on this model

E

-

Mains 'ON' warning light

F

-

Loss of water warning light

Summary of Contents for Thelia 30 E
















Reviews: