background image

2

INTRODUCTION

These instructions describe how to install and

use Saunier Duval appliances. It is important to

pay attention to the warnings on the packaging

and the casing of the appliances, and follow the

information given in this document.

These water-heaters are gas-fired appliances pro-
viding instant hot water to fill a sink or a bath.

The 

OPALIA X13

 water-heater is of the room-sealed

type, that is the venting of combustion products and
the incoming fresh air pass through a flue system.
This venting principle offers a variety of advantages,
such as :
- installation with greatly reduced space require-
ments and with no need for room ventilation;
- a number of installation configurations depending
on the constraints of the premises.

The OPALIA X13 water-heater is of the II

2H3+

 gas

category for use with either natural gas (G20),
butane (G30) or propane (G31)

The water-heater is delivered for a flue system
connection with a top outlet to right or left.

Its variable input means that whatever the rate at
which water is drawn, there will be instantaneous
hot water at a very nearly constant temperature
within the maximum capacity of the appliance.

The ignition system on this water-heater with no
permanent pilot has been designed to achieve
maximum energy saving.

INSTALLATION AND USER INSTRUCTIONS

UK

OPALIA X13

Mandatory warning notice for CEE countries

WARNING,

 this appliance was designed, approved and  inspected to meet the requirements of the English

market.
The identification plate located on the inside of the appliance certifies the origin where the product was
manufactured and the country for which it is intended.
If you see any exception to this rule, please contact your nearest Saunier Duval dealer.
Thank you in advance for your assistance.

INSTALLATION/MAINTENANCE SECTION

Introduction ................................................... Page 2
Dimensions ................................................................ 3
Heater schematic .................................................... 3
Technical data ......................................................... 4
Water heater Installation ........................................ 4
Flue configurations ............................................ 5 - 6
Installation ................................................................. 6
Electric power supply .............................................. 6
Commissioning & Lighting ....................................... 7
Safety devices .......................................................... 7
Servicing / Maintenance ........................................ 8
Draining ..................................................................... 8
Changing gas type ................................................. 8
Fault finding ...................................................... 9 - 10

USER SECTION

Introduction ................................................... Page 2
Commissioning & Lighting ....................................... 7
Safety devices .......................................................... 7
Servicing / Maintenance ........................................ 8
Draining ..................................................................... 8

Summary of Contents for OPALIA X13













Reviews: