SATO SK-270WP-K Instruction Manual Download Page 2

 

Thank you for purchasing the SK-270WP-K Waterproof Digital Thermometer. 
 
- This  product  is  designed  to  measure  temperature  connecting  to  a  dedicated  probe.  Do  not  use  it  for  other 

purposes. 

- Read  this  manual  thoroughly  before  using  the  thermometer.  Keep  the  manual  in  a  safe  place  for  future 

references whenever necessary. 

Warning 

 

The SK-270WP-K digital thermometer is not explosion-proof. Never use it in an atmosphere containing 
flammable gases. 

 

Beware of explosion! 

There is a risk of explosion. Take extreme care. 
 

Whenever you have questions, contact us or the dealer from which the unit was purchased. 

 
 

1. Notes on Use 

Be sure to observe the following precautions in order to use this unit correctly. 
 
- Do not use this unit as a clinical thermometer. 

- Do not drop this unit or apply impact to it. This unit is a precision instrument. 

- Never disassemble or modify this unit. Doing so may result in failure. 

- Do not use this unit in water. 

- Do not use this unit in a place exposed to direct sunlight or near heating equipment. Doing so may result in 

deformation of the casing or failure. 

- Do not use this unit in an environment where electrical noise is generated. Doing so may result in unstable 

display or larger errors. 

- Do not forcibly pull, bend, or bundle the sensor cord. Placing a heavy object on the sensor cord, heating or 

scratching the cord may also damage it. 

- If this unit is not to be used for a long time, always remove the batteries from the unit. Otherwise, the batteries 

may leak fluid, resulting in failure. 

- If the unit becomes dirty, wipe it with a tightly wrung cloth that has been dipped in warm water with neutral 

detergent. Do not wash this unit it in water. 

- Be  sure  to  use  this  unit  within  the  specified  measurement  range.  Using  the  unit  outside  the  specified 

measurement range will result in failure or damage.   

- The penetration type probe has a sharp pointed end so that it can penetrate into the measuring object; as this 

pointed end could cause accidental injuries, handle the probe with due care. 

- Do not use sodium hypochlorite at metallic parts such as probe connector. The sodium hypochlorite is 

effective for disinfecting norovirus, however it corrodes metals. If it adheres to the unit, completely wipe it off 
with a wet cloth. 

**  For repair or calibration, contact us or the dealer from which the unit was purchased. 
 
 

 

 

2. Overview 

The SK-270WP-K is a waterproof digital thermometer to which a dedicated thermistor sensor probe is 
connected.    Optional probes can be interchangeably connected with main unit. 

Summary of Contents for SK-270WP-K









Reviews: