4
"
SURFACE MOUNT
LED FIXTURE
Model: 62-1580, 62-1581, 62-1582, 62-1583, 62-1584, 62-1590
Satco Products, Inc.
Brentwood, NY 11717
INSTALLATION
INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT: Read before installing fixture. Retain for future reference.
© Copyright 2021 Satco Products, Inc. 11/21 v1.3
STEP 1:
Turn OFF power prior to installation.
STEP 2:
Remove existing trim installed in
recessed housing (if necessary). See Figure A.
STEP 3:
Before installation, select your preferred
CCT by moving the switch to either 3000K, 4000K,
or 5000K. See Figure B.
NOTE:
Follow STEP 3 only for fixtures with CCT
selectable capability.
STEP 4:
Connect wires separately (see wiring
diagram). Cap all connections with wire nuts (included).
See Figure C.
STEP 5:
Secure assembly to junction box with screws
(included). See Figure D.
STEP 6:
Reassemble the lamp cover. See Figure E.
STEP 7:
Installation is complete. Turn power ON.
See Figure F.
WARNING: Risk of Fire or Electric Shock
• To avoid damage, falling, electric shock or fire, do not modify the fixture or replace
accessories without confirming with the supplier first.
• Only authorized, qualified personnel should install this fixture and should follow the
owner’s manual. Any improper installation might cause failure, electric shock, fire
or other injury, damage or hazard.
• Disconnect power before installation or any maintenance of the fixture.
• Do not dismantle the fixture without the supplier’s authorization.
• Do not touch the power supply when the fixture is operating.
• Thermal insulating material is not allowed to cover the fixture.
• Keep away from the corrosive substance, and keep the fixture dry and clean.
• The external flexible cable or cord of this fixture cannot be replaced; if the cord is
damaged, the fixture shall be destroyed.
• The electrical fitting must be installed by a licensed electrician.
• For use in environments where an accumulation of non-conductive dust on the
fixture may be expected.
• To prevent fire, this fixture is rated for use in 120VAC.
• The product is for interior use only, suitable for damp location.
• 5 Year limited warranty only in respect of any defect in material.
IMPORTANT:
This product must be installed in accordance with the applicable
installation code by a person familiar with the construction and operation of the product
and the hazards involved.
BLACK
WHITE
GREEN
LINE
NEUTRAL
GROUND
Wiring Diagram
Fixture
5000K
4000K
3000K
A
C
5000K
4000K
3000K
5000K
4000K
3000K
D
F
ø 4.67" (119mm) x 1.31" D (33mm)
Model
CCT (*Selectable)
Watts
Lumens
Volts
CRI
Rated Hours
Operating Temperature
Finish
62-1580
3000K
9W
650
120V
90
50000
-20ºC-40ºC (-4ºF-104ºF)
White
62-1581*
3000K/4000K/5000K
680~720
62-1582*
3000K/4000K/5000K
680~720
62-1583*
3000K/4000K/5000K
680~720
62-1584*
3000K/4000K/5000K
680~720
62-1590
5000K
680
B
E
NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
