background image

 

 

 

 

 

 

4

 

 
 

 
 
 
Dear    buyer  and    user    of    boiler    of    SAS    UWG    type.    This    technical  start-up 
documentation  contains    all  necessary  information  required  for  energy-saving,  safe 
and longstanding exploitation of your boiler.  
We    kindly    ask    you    to    get  familiar    with    documentation  content    prior  to  
assembling  and  starting  the exploitation of a boiler. Hereby documentation shall be 
kept for future use.  
Upon  familiarization  with  this  manual,  the  user  will  be  able  to    utilize  this  device  in  
the  optimum  way.    Careful  reading  of  the  manual  will  help  in  effective  and  safe 
exploitation of the boiler.  

 

 

 

 

 
 
Boilers  of    SAS  UWG  type  are  designated  for  water  installations  of  the  central 
heating  systems,  open  type  with  gravitational    or    forced    water    circulation

*

protected    according  to    presently    being    in    force,  both    domestic  or  the  union 
detailed  regulations  (e.g.  PN-91/B-02413    –  Boilers  of    SAS  UWG  type  installed  in 
accordance  to  hereby  documentation    recommendations  are    not  subject    to    the 
commissioning    led    by    the    Branch  Office    of  Technical  Inspection).    Boilers    are  
specifically    recommended    for    the    flats    heating    in    single-family    homes,  
pavilions,  etc., where calculated feeding water temperature does not exceed 85°C 
and working pressure does not exceed  1,5 bar.   Required  gases draught  pressure  
after    a  boiler  is  0,12  -  0,30  mbar  (depending    on    boiler’s    power).  These  boilers 
may also work in hot water installations utilizing a heat exchanger.  
Boiler’s selection for building heating should be based on heat balance, according to 
regulations in force, both domestic and the union (e.g. PN-B-02025:2001). 

 
 
 
 

 
 
 
The  coal  heating  boiler  of   SAS  UWG  type  is  a  modern  construction  heating  
device    with    lower  combustion  of    solid    fuels.      Boiler’s    body    consists    of  
combustion    part    and    convection    section.  Boiler    is  made  of  steel  metal  sheet 
welded type. 
Front    chamber    (pos.    4)    serves    as  a    furnace    with    water    grates.  Below    the  
grate    there    is    the    ash    box  .      Boiler’s  basic  components  are  presented  on  the 
drawing (p. 11-12). 

                                                 

*

 Asseblied installation must conform  the detailed requirements of local standards for the heating devices 

protection measures, requirements for open water systems and pressurized vessels of open systems. 

1.

  

INTRODUCTION

 

2.

  

USE OF BOILER

 

3.

  

BOILER CONSTRUCTION DESCRIPTION

 

Summary of Contents for UWG





















Reviews: