Sarka SSG-400 Owner'S Manual Download Page 7

4

Troubleshooting

We recommend a periodic inspection of the grill to maintain safe and proper operation. This should occur every 3 months. We also recommend that you 

clean your grill at the same time. A clean grill will look better, operate better and grill safer. There are several telltale signs to look for when inspecting your 

grill. They are listed below along with the recommended solutions.

1. Yellowish flame and/or sooty bottom of catch pan

Cause: Spiders. This is a common problem with gas grills. The additive used to give propane its odor attracts spiders. The spider will nest 

in the burner.

Solution: Remove the burner from the grill by lifting the burner off the igniter bracket.

Use a drinking straw or pipe cleaner to clean the burner intake and ports.

2. Unable to light your grill

If ignition does not immediately take place, turn the burner valve to off, wait 5 minutes, and repeat the lighting procedure.’

Causes: No gas to burner, no spark.

Solutions:

A. Check gas supply to insure that supply is present.

B. Open hood, make sure the gas valve is off, and check for spark from igniter electrode to burner. If no spark is seen,

 check end of wire to insure that it is properly connected to the igniter.

 If you still have no spark, the igniter may be bad. Contact your local dealer for replacement part.

C. If a small spark is seen near the point where the electrode is fastened to the igniter bracket, the electrode may be

 cracked. Contact your local dealer for replacement part

D. In rare instances, if the weather has been unusually wet, there may not be a good ground between the burner and

electrode.

 Check the electrode end as well as the edge of the burner closest to the electrode for moisture or foreign matter. 

E. Consult your local dealer.

Never check for leaks or malfunctions with an open flame. Never check line connections with an open flame.

3. Excessive grease in the catch pan or inside the grill

Cause:   Grilling extremely fatty foods

       Grilling temperature is too low

Solutions: 

A. Drain excess grease from catch pan and operate on high Temperature for 15-20 minutes. The grill should be attended

 during this procedure.

B. Grill at 475-500 degrees

C. Postheat grill for 15 minutes after use.

To Reorder Grill Parts 

Contact:

Sarka Bros.

607 Ottawa Street

P.O. Box 316

Kalida, OH 45853

Ph: 419-532-2393

Fax: 419-532-2405

Warranty Registration Card

First Name 

   Initial            Last Name

Street

City

State

Zip

Model

Serial 

Number

Date of Purchase 

Purchase Location

Please Print Clearly

Cut and Mail

Summary of Contents for SSG-400










Reviews: