Sargent SE LP10 7000 Series, Installation Instructions Manual

Page: 5 / 20

05/31/18
Copyright © 2018, Sargen
t Manufacturing Company
, an A
SS
A AB
LO
Y G
roup company
. All right
s reser
ved
.
Reproductions in whole or in par
t without express writ
ten permission of Sargen
t Manufacturing Company is prohibited
.
A8239A • 800-810-WIRE (9473) • www.sargentlock.com
5
SE LP10 7000 Series Multi Point Lock
Total
One-Way
Length of
Wire Run (ft)
Load Current @ 12VDC
1/4A 1/2A 3/4A 1A 1-1/4A 1-1/2A 2A 3A
100 20 18 16 14 14 12 12 10
150 18 16 14 12 12 12 10 —
200 16 14 12 12 10 10 — —
250 16 14 12 10 10 10 — —
300 16 12 12 10 10 — — —
400 14 12 10 — — — — —
500 14 10 10 — — — — —
750 12 10 — — — — — —
1,000 10 — — — — — — —
1,500 10 — — — — — — —
Wire Gauge Charts
Total
One-Way
Length of
Wire Run (ft)
Load Current @ 24VDC
1/4A 1/2A 3/4A 1A 1-1/4A 1-1/2A 2A 3A
100 24 20 18 18 16 16 14 12
150 22 18 16 16 14 14 12 10
200 20 18 16 14 14 12 12 10
250 18 16 14 14 12 12 12 10
300 18 16 14 12 12 12 10 —
400 18 14 12 12 10 10 — —
500 16 14 12 10 10 — — —
750 14 12 10 10 — — — —
1,000 14 10 10 — — — — —
1,500 12 10 — — — — — —
5
Strip 1/4”
Overlap wires as shown. Use heat gun to set wires.
Wiring Diagrams
*Diagrams on following pages
Default Operation Mode:
• Red LED ‘ON’ when powered.
• Presenting a 13.56 MHz or 125 kHz credential causes LED to briefly
turn green and then return to red state.
• Presenting a FIPS 201 PIV credential causes LED to turn amber as
credential is authenticated. Reader emits a short beep when
credential is successfully read. Reference *Diagram #1.
Optional Operation Mode:
Connect selected TAMPER wire from reader to ElectroLynx cable pin 8.
Note: For fire rated doors solder sleeve (P/N 52-1373) to be applied to
desired lead 2.5” from base of reader. See diagram for application.
Connect Yellow TAMPER wire from ElectroLynx cable to desired EAC panel
control line.
As appropriate, use configuration card to activate desired mode on reader.
PIN8 (Yellow – TAMPER)
PIN 6 (Blue – RX COM)
PIN 4 (Green – Data 0)
PIN 2 (Red – Reader POS)
PIN 1 (Black – Reader NEG)
PIN 3 (White – Data 1)
PIN 5 (Orange – RX NO)
PIN 7 (Brown - EGND)
PIN 4 (Tan – DPS COM)
PIN 2 (Gray – Lock POS)
PIN 1 (Violet – Lock NEG)
PIN 3 (Pink – DPS NC)
Note: When Yellow TAMPER wire is tied directly into EAC panel relay, no AC signals should be applied on wire or door reader performance will be impacted.
8 PIN CONNECTOR 4 PIN CONNECTOR
1-Black 2-Red 3-White 4-Green 5-Orange 6-Blue 7-Brown 8-Yellow 1-Violet 2-Gray 3-Pink 4-Tan
12VDC
(Reader)
WIEGAND WIEGAND RX RX EGND TAMPER 12/24 VDC
(LOCK RELAY)
DPS
(NC)
DPS
(COM)
NEG POS DATA_1 DATA_0 NO COM EGND OPEN
COLLECTOR
NEG POS DPS DPS
The SE LP10 reader can be configured for various modes of LED and beeper operation. HID programming
cards are supported to configure the behavior for LED and beeper activity. Call 1-800-810-WIRE (9473) for
details. Along with the programming cards, the TAMPER wire can be connected within the panel and the
lock in order to enable some of the listed features.
Wire Gauge Charts