manualshive.com logo in svg

Sargent Passport 1000 PG, Installation Instructions Manual, Page: 14 / 28

Share
Download
Sargent Passport 1000 PG Installation Instructions Manual Download Page 14

7  

Installation Instructions for                       

Mortise Type Exit Device 

8977/8978

IMPORTANT BEFORE STARTING: 
•

 This device is non-handed. 

•

 Door should be fitted and hung.  

•

 Verify box label for size of exit device, 

function and hand. 

 If using a mullion, install in frame.  

Outside of door  

Through-

bolt holes  

Controller 

cutout  

Motor wire 

channel  

Cylinder 

hole  

ET lever 

hole  

ET through-

bolt holes  

Fig. 1A  

Mortise 

pocket  

Through-bolt 

holes  

Backplate mount 

holes

Cylinder 

hole  

Chassis lever 

hole 

ET through-bolt 

holes  

Inside of door 

Controller 

cutout 

Wire run 

channel 

Motor wire 

channel  

Chassis mount 

holes  

1 – Exit Hardware and Door Preparation  

NOTE: Instruction examples show   

       wood door installation.      
       For metal doors, route     
       cables inside door.  

Left Hand Reverse 

LHR

Right Hand Reverse 

RHR

Inside

Outside

Prior to installation, all holes must be free of burrs, debris and sharp edges.
If doors are not properly reinforced per ANSI 115.2, commercially available reinforcements should be installed. 
Prepare door according to exit installation instructions  A6705 and appropriate template:
 

• Field templates 

A7460 and A7461 

(for wood doors).

 

• Manufacturer’s templates 

4537 and 4538

 (for metal doors).

10/31/12

A7809B                14

Copyright © 2012, Sargent Manufacturing Company

, an ASSA ABLOY Group company

. All rights reser

ved. 

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

Passport 1000 PG Exit Device

Summary of Contents for Passport 1000 PG





























Reviews:

No comments