background image

5

 CAMER
 PRESE
 AUTO 
 AUTO 
·ALARM
 PASSW
 LANGU
 OPTIO

 PRESE
 MENU

     A
·ALARM 
 ALARM 
 MOTIO
 uAREA
 uSENS
 ZOOM

RED
BLACK
WHITE
YELLOW
PURPLE
ORANGE
BLUE
GRAY

YELLOW
PURPLE
GRAY
WHITE

RS-48
RS-48

UTP
UTP

GND

DAY/NIGHT
ALARM IN1
ALARM IN2

ALARM OUT

COMMON

DC12 AC24

+

~
~

~
~

GND

+

Connections

BNC type

RG-6U, 300 m or less

For the connection, use a RG-6U coaxial 
cable.

Monitor Connection

b

With AC 24 V

Power Supply Connection

• Using different cables from those 

specified here may attenuate the 
video and/or sync signals and 
interfere with correct transmission.

• RG-59U coaxial cables can be 

used when distance between 
devices is short, but not in duct or 
aerial routing.

Cable type

Length

RG-59U (3C-2V)

150 m max.

RG-6U (5C-2V)

300 m max.

RG-11U (7C-2V)

350 m max.

b

With DC 12 V

Check that +/- polarity is correct.

(RED)

(BLACK)

(WHITE)

For the connections, use cables thicker than 
18 AWG.

(RED)

(BLACK)

To prevent electromagnetic 
interference

• On the cable for power supply

Be sure to attach the supplied clamping 
core to the cables as illustrated.

For the connections, use cables thicker than 
18 AWG.

Connection for a communication device 
for remote operation

Do not connect the power cord until all other 
connections have been completed.

Note:

L5BL2_XE(INSTALLATION).book  5 ページ  2006年6月23日 金曜日 午後7時9分

Summary of Contents for VDC-DP9584S









Reviews: