background image

INSTALLATION MANUAL

Color CCD Camera

THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED 
SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL 
CODES.

Please read this manual before installing and using this unit, and always follow the instructions 
in it for proper use. Please also read the separate INSTRUCTION MANUAL before using the unit 
for proper use.

This unit can be installed on the ceiling or wall. 
When installing, first remove the built-in camera 
from the unit.

b

When routing the cables on ceiling or wall 
surfaces:

Loosen the conduit hole cover fixing screw 

(A)

 on 

the back of the camera unit base with the hexagonal 
wrench (small), open the cover 

(B)

, and pass the 

connection cables through the conduit hole.

b

Replacement timing of major parts

If the unit is used continuously, parts will 
become worn and deteriorated depending on 
the environment of use.
It is recommended that parts be replaced 
approximately every 2 years (approximately 
1,200,000 times) in order to maintain unit 
performance.

• Motor, cables used in mechanical parts, 

gears, etc.

Since the conduit hole cover is not 
waterproof-finished, always be sure to 
seal the cover entirely by puttying, for 
example, upon completion of installation.

Ceiling Installed (see page 1)

Wall Installed (see page 3)

(In-ceiling routing)

(Surface routing)

(In-wall routing)

(Surface routing)

Important

• Be careful when opening holes for installing 

the unit. Work with the power and video 
cables pulled out for easy installation.

• Make sure to properly perform waterproofing 

for the ceiling or wall where you are installing 
the unit.

• Make sure that the surface in the installation 

location has no unevenness and is strong 
enough to bear the total weight of the unit.

• Install this unit in an environment where the 

temperature range stays between -10°C 
and +50°C (no condensation allowed).

• As a precaution against static electricity 

damage, touch a nearby metal object (door 
knob, etc.) to dissipate static electricity in 
your body before touching this unit.

A

B

VDC-DP9585P

E

ngl

is

h

F

ran

çai

s

Deutsc

h

中文

简体

L5BL2_XE(INSTALLATION).book  0 ページ  2006年6月23日 金曜日 午後7時9分

Summary of Contents for VDC-DP9584S









Reviews: