Sanyo PLC--XP200L, Service Manual

Page: 53 / 154

-53-
Electrical Adjustment
Grp / No. Item Function Range Initial Note
107 CXD3540_VS
0 VS_GSEL 0 ~ 3 0
1 VS_R_RGT 0 ~ 1 1
2 VS_G_RGT 0 ~ 1 0
3 VS_B_RGT 0 ~ 1 1
4 VS_CYCLE 0 ~ 1 0
5 VS_ON 0 ~ 1 0
6 VS_GDAT1 0 ~ 255 0
7 VS_DAT 0 ~ 255 0
8 VS_GDAT3 0 ~ 255 0
9 VS_GDAT2 0 ~ 255 0
108 CXD3540_DSDPOST1
0 HXT_TH4_ON 0 ~ 1 0
1 HXT_TH3_ON 0 ~ 1 0
2 HXT_TH2_ON 0 ~ 1 0
3 HXT_TH1_ON 0 ~ 1 0
4 HXT_ON 0 ~ 1 0
5 HXT_RCALC 0 ~ 1 0
6 HXT_GCALC 0 ~ 1 0
7 HXT_BCALC 0 ~ 1 0
8 HXT_GSEL 0 ~ 1 0
9 HXT_RDAT1 0 ~ 255 0
10 HXT_RDAT2 0 ~ 255 0
11 HXT_RDAT3 0 ~ 255 0
12 HXT_GDAT1 0 ~ 255 0
13 HXT_GDAT2 0 ~ 255 0
14 HXT_GDAT3 0 ~ 255 0
15 HXT_BDAT1 0 ~ 255 0
16 HXT_BDAT2 0 ~ 255 0
17 HXT_BDAT3 0 ~ 255 0
18 HXT_TH1 0 ~ 255 0
19 HXT_TH2 0 ~ 255 0
20 HXT_TH3 0 ~ 255 0
21 HXT_TH4 0 ~ 255 0
22 SEL_MODE2 0 ~ 7 0
200 Option
0 Logo Display Prohibition 0:Menu 1:Forced 0 - 1 0
1 RS232C Baudrate 0: 19200bps 1: 9600bps 0 - 1 0
3 Shipping Set Shipping set when the value is set to 10 0 - 20 0
4 CABLE SW Long Cable 0: Disable 1: Enable 0 - 1 0
5 PW Debug Command Enable
0: Disable (Sanyo Serial Command Enable)
1: Enable (PW Debug Mode)
0 - 1 0
6 Device Refresh Disable 0: Enable 1: Disable 0 - 1 0
8 PJ-NET Hung up check 0: Enable 1: Disable 0 - 1 0
20 Projector Time Reset Reset when the value to set to 10 0 -
１
0 0
21 Lamp Warning Time (NORMAL) 1-16 4
22 Lamp Warning Time (ECO) 1-16 6
23 Lamp Warning Time (HIGH) not supported 1-16
50 Lamp Replacement Display 1:On 0:Off 0 - 1 1
51 Filter Warning Display 1:On 0:Off 0 - 1 1
52 Lamp Counter Reset Times Read only 0 - 255 0
53 Filter Counter Reset Times Read only 0 - 255 0
54 Factory Default Execute Times Read only 0 - 255 0
55 Motor Operation Stop 0: Enable 1: Disable 0 - 1 0
58 Lamp Go Out Lamp goes out 0 - 1 0
70 ADC Device Select for Analog PC 0 = ISL51002, 1 = PW392 AFE 0 - 1 0
71 ADC Device Select for Component 0 = ISL51002, 1 = PW392 AFE 0 - 1 0
80 Destination Language Set at Shipping 0:English １ :Japanese 0 - 1 0
100 Disable Auto Picture Control 0 : Normal operation 1 : Auto Picture Control Off 0-1 Initial: 1 Shipping 0
201 Option (Signal) Not Used
0 FrameLock Option Frame Lock Setting 0: Normal(Auto) 1: OFF 0 - 1 0
1 Dither Enable 0: Disable 1: Enable 0 - 1 0
204 Simulation mode
0 PW392C Enable 0: Off, 1: On 0 - 1 0
1 PW610 Enable 0: Off, 1: On 0 - 1 0